ENGINE SWITCH INSTALLATION


  1. INSTALL ENGINE SWITCH


    1. A017G2F

      Engage the 2 claws to install the switch.

    2. Connect the switch connector.

  2. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)


    1. A017FLQ

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <E> and 2 clips.

  3. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)


    1. A017BQH

      Engage the claw and 2 guides.

    2. Install the front No. 2 console box insert with the 3 screws <E> and clip.

  4. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017E8O

      Engage the 6 claws.

    2. Connect the connector.

    3. A017C3F

      Install the console box assembly with the 4 bolts and 2 screws.

  5. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017G3R

      Engage the 6 claws.

    2. A017E57

      Install the console box assembly with the 4 bolts and 2 screws.

  6. INSTALL LOWER REAR CONSOLE BOX


    1. Install the lower rear console box.

  7. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    1. A017F5N

      Install the No. 2 console box duct as shown in the illustration.

  8. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Connect the connector.

    2. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.

  9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    1. A017CWD

      Connect the hood lock control cable assembly.

    2. Connect each connector and the aspirator duct.

    3. A017EU2

      Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    1. A017BY3

      Connect the hood lock control cable assembly.

    2. Connect each connector.

    3. Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Engage the claw and clip, install the cowl side trim sub-assembly LH.

    2. Install the clip.

  12. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Engage the guide and 8 claws, and install the front door scuff plate LH.

  13. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017EE0

      Engage the 4 clips and install the air conditioning control assembly.

  14. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    1. Connect the connector.

    2. A017G04

      Engage the 4 clips and install the heater control and accessory assembly.

  15. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017D5UE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.