ENGINE SWITCH REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag deployment and seat belt pretensioner activation.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017EABE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  3. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    1. A017G04

      Disengage the 4 clips and remove the heater control and accessory assembly.

    2. Disconnect the connector.

  4. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    1. A017EE0

      Disengage the 4 clips and remove the air conditioning control assembly.

    2. Disconnect the connector.

  5. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Disengage the 8 claws and guide, and remove the front door scuff plate LH.

  6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Remove the clip.

    2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.

  7. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    1. A017EU2

      Remove the 2 bolts <B>.

    2. Disengage the 3 claws and 10 clips.

    3. A017CWD

      Disconnect each connector and the aspirator duct.

    4. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.

  8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    1. A017EU2

      Remove the 2 bolts <B>.

    2. Disengage the 3 claws and 10 clips.

    3. A017CWD

      Disconnect each connector and the aspirator duct.

    4. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.

  9. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Disengage the 4 claws and 4 clips.

    2. Disconnect the connector and remove the upper console panel sub-assembly.

  10. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    1. A017DWP

      Remove the No. 2 console box duct as shown in the illustration.

  11. REMOVE LOWER REAR CONSOLE BOX


    1. Remove the lower rear console box.

  12. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017E57

      Remove the 4 bolts and 2 screws.

    2. A017G3R

      Disengage the 6 claws and remove the console box assembly.

  13. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017C3F

      Remove the 4 bolts and 2 screws.

    2. A017E8O

      Disconnect the connector.

    3. Disengage the 6 claws, and remove the console box assembly.

  14. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)


    1. A017FLQ

      Using a clip remover, remove the 2 clips.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.

  15. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)


    1. A017BQH

      Using a clip remover, remove the clip.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.

  16. REMOVE ENGINE SWITCH


    1. A017G2F

      Disconnect the switch connector.

    2. Disengage the 2 claws and remove the switch.