Click here

SMART ENTRY AND START SYSTEM Power Source Mode does not Change

Click here
Click here
DTC Code DTC Name
  Power Source Mode does not Change
Click here

DESCRIPTION

When the engine switch is pushed with the electrical key in the cabin, the main body ECU receives signals to switch the power source mode.

Tip:

To allow use of the intelligent tester to inspect the push-button starting function when the engine switch is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the intelligent tester and the main body ECU. (Opening and closing a door can also be simulated by operating a door courtesy light switch.)

A017BJIE04
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    CHECK SMART ENTRY AND START SYSTEM


    1. A017BOOE01

      Remove the battery of the electrical key transmitter (Click here).

    2. Touch the logo side of the key or card key to the engine switch.

    3. Check that power source mode can be changed to on (IG and ACC).

      Result
      Result Proceed to
      Power source mode does not change to on (ACC) A
      Power source mode does not change to on (IG) B
      Power source mode does not change to on (IG and ACC) C
      Power source mode is turned on D

  2. Click here

    INSPECT ACC RELAY


    1. A017B6EE23

      Remove the ACC relay from the instrument panel junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified condition
      3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 When battery voltage is applied to terminals 1 and 2 Below 1 Ω

  3. Click here

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK)


    1. A017C94E37

      Disconnect the D7 connector from the main body ECU.

    2. Disconnect the 1I connector from the instrument panel junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified condition
      D7-22 (ACCD) - 1I-3 Always Below 1 Ω
      D7-22 (ACCD) or 1I-3 - Body ground Always 10 kΩ or higher

  4. Click here

    INSPECT IG1 RELAY


    1. A017EO0E45

      Remove the IG1 relay from the instrument panel junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester connection Condition Specified condition
      3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 When battery voltage is applied to terminal 1 and 2 Below 1 Ω

  5. Click here

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK)


    1. A017C94E38

      Disconnect the D7 connector from the main body ECU.

    2. Disconnect the 1I connector from the instrument panel junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester connection Condition Specified condition
      D7-3 (IG1D) - 1I-9 Always Below 1 Ω
      D7-3 (IG1D) or 1I-9 - Body ground Always 10 kΩ or higher

  6. Click here

    INSPECT IG2 RELAY


    1. A017B6EE23

      Remove the IG2 relay from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester connection Condition Specified condition
      3 - 5 When battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 When battery voltage is applied to terminal 1 and 2 Below 1 Ω

  7. Click here

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - IG2 RELAY)


    1. A017CREE02

      Disconnect the D6 connector from the main body ECU.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester connection Condition Specified condition
      D6-11 (IG2D) - Engine room relay block IG2 relay terminal 1 Always Below 1 Ω
      D6-11 (IG2D) or Engine room relay block IG2 relay terminal 1 - Body ground Always 10 kΩ or higher

  8. Click here

    CHECK HARNESS AND CONNECTOR (BATTERY - IG2 RELAY)


    1. A017CLRE01

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester connection Condition Specified condition
      Engine room relay block IG2 relay terminal 5 - Body ground Always 11 to 14 V

  9. Click here

    CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)


    1. A017CLRE01

      Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester connection Condition Specified condition
      Engine room relay block IG2 relay terminal 2 - Body ground Always Below 1 Ω

  10. Click here

    CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK)


    1. A017C6LE02

      Disconnect the 1A connector from the instrument panel junction block.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester connection Condition Specified condition
      1A-1 - Body ground Always 11 to 14 V

  11. Click here

    CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BODY GROUND)


    1. A017ENSE02

      Disconnect the 1F connector from the instrument panel junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester connection Condition Specified condition
      1F-10 - Body ground Always Below 1 Ω

  12. Click here

    GO TO SMART ENTRY AND START SYSTEM (ENTRY)Click here

  13. Click here

    REPLACE ACC RELAY

  14. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. Click here

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  16. Click here

    REPLACE IG1 RELAY

  17. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  18. Click here

    REPLACE IG2 RELAY

  19. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  20. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE IG2 FUSE

  21. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  22. Click here

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  23. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ALT FUSE

  24. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  25. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR