Click here

GENERATOR REMOVAL

Click here
Click here
  1. Click here

    REMOVE FRONT WHEEL RH

  2. Click here

    REMOVE ENGINE UNDER COVER ASSEMBLY


    1. A017FPR

      Remove the 2 bolts and engine under cover assembly RR.

    2. A017FXN

      Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.

  3. Click here

    REMOVE NO. 1 ENGINE UNDER COVER


    1. A017D1W

      Remove the 6 bolts, 2 clips and No. 1 engine under cover.

  4. Click here

    REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

    Tip:

    Use the same procedures for the RH side and LH side (Click here).

  5. Click here

    REMOVE FRONT FENDER LINER RH


    1. A017B7YE01

      Remove the screw.

    2. Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

    3. A017CZV

      Using a 4 mm hexagon wrench, remove the 2 screws.

    4. Remove the 3 grommets.

      Tip:

      The grommets need to be replaced with new ones because they will break when they are removed.

    5. A017CFW

      Remove the 5 clips

    6. Remove the bolt, 8 screws and front fender liner RH.

  6. Click here

    REMOVE FRONT FENDER APRON SEAL RH


    1. A017FOB

      Remove the 2 bolts, clip and front fender apron seal RH.

  7. Click here

    DRAIN ENGINE COOLANT


    1. A017CW8E01

      Loosen the radiator drain cock plug.

      Tip:

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. Remove the radiator cap sub-assembly from the radiator assembly.

      Note:

      Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    3. Loosen the 2 cylinder block drain cock plugs.

  8. Click here

    REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A017EFM

      Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

      Note:

      Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.

  9. Click here

    REMOVE COOL AIR INTAKE DUCT SEAL


    1. A017CN1

      Remove the 11 clips and cool air intake duct seal.

  10. Click here

    REMOVE BATTERY

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


    1. A017FMC

      Loosen the nut, and disconnect the negative battery terminal.

    2. Loosen the nut, and disconnect the positive battery terminal.

    3. Loosen the nut, and remove the bolt and battery clamp.

    4. Remove the battery and battery tray.

  11. Click here

    REMOVE NO. 2 AIR CLEANER INLET


    1. A017D82

      Disconnect the 2 vacuum switching valve clamps.

    2. Disconnect the 2 vacuum hoses.

    3. Remove the 2 bolts and No. 2 air cleaner inlet.

  12. Click here

    REMOVE NO. 1 AIR CLEANER INLET


    1. A017C2Q

      Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.

  13. Click here

    DISCONNECT NO. 1 RADIATOR HOSE


    1. A017EYO

      Disconnect the No. 1 radiator hose from the radiator.

  14. Click here

    DISCONNECT NO. 2 RADIATOR HOSE


    1. A017FFS

      Disconnect the No. 2 radiator hose from the radiator.

  15. Click here

    DISCONNECT OIL COOLER HOSE


    1. A017F5B

      Disconnect the oil cooler hoses from the radiator.

  16. Click here

    DISCONNECT COOLING FAN ECU CONNECTOR


    1. A017FVV

      Detach the wire harness clamps from the fan shroud LH side.

    2. A017DKS

      Detach the wire harness clamps from the fan shroud RH side and disconnect the cooling fan ECU connector.

  17. Click here

    REMOVE RADIATOR GRILLE SUB-ASSEMBLY


    1. A017D07E01

      Put protective tape around the radiator grille sub-assembly.

      Table 1. Text in Illustration
      *1 Protective Tape
    2. A017DG7

      Remove the 6 clips.

    3. Disengage the 8 claws and 2 guides, and remove the radiator grille sub-assembly.

  18. Click here

    REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    1. A017D3E

      Remove the hood lock nut cap.

    2. A017CPZ

      Remove the 3 bolts.

    3. A017DBV

      Disconnect the hood lock control cable and remove the hood lock assembly.

  19. Click here

    REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    1. A017EVU

      Disconnect the connector.

    2. A017FVJ

      Remove the hood lock nut cap.

    3. A017CI6

      Remove the 3 bolts.

    4. A017BQ6

      Disconnect the hood lock control cable and remove the hood lock assembly.

  20. Click here

    REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for LHD)


    1. A017FE9

      Disconnect the low pitched horn and high pitched horn connectors.

    2. A017E8C

      Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.

  21. Click here

    REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for RHD)


    1. A017FE9

      Disconnect the low pitched horn and high pitched horn connectors.

    2. A017C96

      Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.

  22. Click here

    SEPARATE COOLER CONDENSER ASSEMBLY


    1. A017CEX

      Remove the 4 bolts and move the cooler condenser assembly to remove the radiator assembly and fan assembly with motor.

  23. Click here

    REMOVE RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR


    1. A017G1R

      Remove the radiator assembly and fan assembly with motor.

  24. Click here

    REMOVE NO. 2 OIL LEVEL DIPSTICK GUIDE


    1. A017BP5

      Remove the bolt and the No. 2 oil level dipstick guide.

  25. Click here

    REMOVE V-RIBBED BELT


    1. A017F8UE01

      Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.

      09961-00950
    2. A017FUV

      While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.

  26. Click here

    REMOVE GENERATOR ASSEMBLY


    1. A017FW6

      Remove the terminal cap.

    2. Remove the nut and disconnect the wire harness from terminal B.

    3. Disconnect the generator connector from the generator assembly.

    4. Disconnect the connector from the compressor and magnetic clutch.

    5. Disconnect the 3 wire harness clamps.

    6. A017D5C

      Remove the 2 bolts, and then disconnect the bracket.

    7. A017CS4

      Remove the 2 bolts and the generator assembly.

    8. A017FOZ

      Disconnect the wire harness clamp, and then remove the generator bracket.

    9. A017BV6

      Remove the bolt and the wire harness clamp bracket.