SMART ENTRY AND START SYSTEM DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.


    1. Connect the intelligent tester to the DLC3.

      When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 or less second intervals until communication between the tester and vehicle starts.

    2. Turn the engine switch on (IG).

    3. Read the DATA LIST.

      Body:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Engine switch on (ACC) / ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -
      IG SW Engine switch on (IG) / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Stop Light SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      St SW1 Start switch 1 / ON or OFF

      ON: Engine switch is pushed

      OFF: Engine switch is not pushed

      		 -
      St SW2 Start switch 2 / ON or OFF

      ON: Engine switch is pushed

      OFF: Engine switch is not pushed

      		 -
      Str Unlock SW Steering lock condition / ON or OFF

      ON: Steering is unlocked (Engine switch on (ACC))

      OFF: Steering is locked (Engine switch off)

      		 -
      N SW / C SW Park/Neutral position switch / ON or OFF

      ON: Shift position is P or N

      OFF: Shift position is except P and N

      		 -
      SHIFT P SIG Shift P position signal / ON or OFF

      ON: Shift position is P

      OFF: Shift position is not P

      		 -
      Vehicle Spd Sig Vehicle speed signal / STOP or RUN

      STOP: Vehicle is stopped

      RUN: Vehicle is running

      		 -
      E/G Cond Engine condition / STOP or RUN

      STOP: Engine is stopped

      RUN: Engine is running

      		 -
      IG1 Relay Mon1 IG1 relay monitor (outer) / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      IG2 Relay Mon1 IG2 relay monitor (outer) / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      IG1 Relay Mon2 IG1 relay monitor (inner) / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      IG2 Relay Mon2 IG2 relay monitor (inner) / ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      ACC Relay Mon ACC relay monitor / ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -
      Ratch Circuit Ratch circuit / ON or OFF

      ON: Engine switch on (IG) or engine is running

      OFF: Engine switch off or on (ACC)

      		 -
      Start Req Sig Starter request signal monitor / ON or OFF

      ON: Starter relay is ON

      OFF: Starter relay is OFF

      		 Engine switch pressed and held with shift lever in the P or N position
      Pwr Cond Power supply condition / ALL, ACC ON, IG1 IG2, ST ON

      ALL: All relays are OFF

      ACC ON: ACC relay is ON

      IG1: IG1 relay is ON

      IG2: IG2 relay is ON

      ST ON: ST request signal is ON

      		 -
      ACC Cut Sig ACC relay cut signal / ON or OFF

      ON: Engine is cranking

      OFF: Engine is not cranking

      		 -
      St Relay Mon STARTER relay monitor / ON or OFF

      ON: Engine is cranking

      OFF: Engine is not cranking

      		 Engine is cranking with engine switch on (IG) and shift lever in P or N
      Comm Smrt/Wrls Communication for certification ECU (smart key ECU assembly) / OK or STOP

      OK: Communication

      STOP: No communication

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform ACTIVE TEST allows the relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing the ACTIVE TEST early in troubleshooting is one way to save diagnostic time. The DATA LIST can be displayed while performing ACTIVE TESTs.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Perform the ACTIVE TEST according to the display on the tester.

    Body:
    Tester Display Test Part Control Range Diagnostic Note
    Lighting Ind Indicator for lighting ON / OFF -
    Ind Condition Engine switch indicator Green / Amber / No Sig -
    S Lock Pwr Power supply for steering lock ECU ON / OFF -