Click here

OIL AND OIL FILTER REPLACEMENT

Click here
Click here
CAUTION:

  • Prolonged and repeated contact with engine oil will result in removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to preserve the environment, used oil and used oil filters must be disposed of at designated disposal sites.

Click here
  1. Click here

    DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil drain plug and gasket, and drain the oil into a container.

    3. Clean and install the oil drain plug with a new gasket.

      40 N*m 408 kgf*cm 30 ft.*lbf
  2. Click here

    REMOVE OIL FILTER ELEMENT


    1. Remove the oil filter element service hole cover.

    2. A017GC1E01

      Connect a hose with an inside diameter of 15 mm (0.59 in.) to the pipe.

    3. A017BSK

      Remove the oil filter drain plug from the oil filter cap.

    4. A017CO9E01

      Insert the pipe with the hose into the oil filter cap.

      Note:

      Be sure to insert the pipe with the O-ring installed on the oil filter cap side.

      Tip:

      Place the hose end into a container before draining oil from the hose.

    5. A017F0F

      Make sure that oil is completely drained, and remove the pipe and O-ring.

      Tip:

      Be sure to angle the pipe in the direction of the arrow to remove it.

    6. A017FTIE01

      Using SST, remove the oil filter cap.

      09228-06501
    7. A017BLCE03

      Remove the oil filter element and O-ring from the oil filter cap.

      Note:

      Do not use any tools to remove the O-ring in order to prevent the cap from being damaged. Be sure to remove it by hand.

  3. Click here

    INSTALL OIL FILTER ELEMENT


    1. A017BLCE03

      Clean the inside of the oil filter cap, threads, and O-ring groove.

    2. Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

      Note:

      Make sure that the O-ring does not get twisted on the groove.

    3. Install a new oil filter element to the oil filter cap.

    4. Remove all dirt and foreign matter from the contact surfaces and the inside of the cap on the engine side.

    5. Apply a light coat of engine oil to the O-ring again and install the oil filter cap.

      Note:

      Make sure that the O-ring does not get caught between the parts.

    6. A017F0VE01

      Using SST, install the oil filter cap.

      09228-06501
      25 N*m 255 kgf*cm 18 ft.*lbf
      Note:

      Make sure that there is no clearance between the parts after tightening the oil filter cap.

    7. A017CLQE01

      Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

      Note:

      Remove all dirt and foreign matter from the contact surfaces.

    8. Install the oil filter drain plug to the oil filter cap.

      13 N*m 127 kgf*cm 10 ft.*lbf
      Note:

      Make sure that the O-ring does not get caught between the parts.

  4. Click here

    ADD ENGINE OIL


    1. Add clean engine oil and install the oil filler cap.

      Engine oil
      Oil Grade Oil Viscosity (SAE)

      .API grade SL and energy-conserving

      .API grade SM and energy-conserving

      .ILSAC multigrade engine oil

      		 10W-30
      API grade SL 15W-40
      API grade SM 20W-50
      Table 1. Standard capacity (w/ Oil Cooler):
      Item Standard Condition
      Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 lmp. qts)
      Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 lmp. qts)
      Dry fill 7.1 liters (7.5 US qts, 6.2 lmp. qts)
      Table 2. Standard capacity (w/o Oil Cooler):
      Item Standard Condition
      Drain and refill with oil filter change 6.1 liters (6.4 US qts, 5.4 lmp. qts)
      Drain and refill without oil filter change 5.7 liters (6.0 US qts, 5.0 lmp. qts)
      Dry fill 6.8 liters (7.2 US qts, 6.0 lmp. qts)
  5. Click here

    INSPECT FOR OIL LEAK


    1. Start the engine.

    2. Check for engine oil leaks from the oil filter cap and oil filter drain plug.

    3. Install the oil filter element service hole cover.