Click here

COOLING FAN SYSTEM Cooling Fan Circuit

Click here
Click here
DTC Code DTC Name
  Cooling Fan Circuit
Click here

DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed, and vehicle speed and sends the signals to the cooling fan ECU to regulate the cooling fan. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness. The cooling fan speed is determined based on engine coolant temperature, air conditioner operating conditions, engine speed, and vehicle speed.

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE COOLING FAN)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cooling Fan.

    4. Check the operation of the cooling fan while operating it using the intelligent tester.

      OK
      The cooling fan rotates.

  2. Click here

    REPLACE ECMClick here

  3. Click here

    CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)


    1. A017F4EE02

      Disconnect the D31 connector from the ECM.

    2. Disconnect the cooling fan ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      D31-14 (RFC) - A9-2 (SI) Always Below 1 Ω

  4. Click here

    INSPECT NO. 1 COOLING FAN MOTOR


    1. A017G4XE01

      Disconnect the No. 1 cooling fan motor connector.

    2. Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 1 cooling fan motor connector.

      OK
      The No. 1 cooling fan rotates.

  5. Click here

    INSPECT NO. 2 COOLING FAN MOTOR


    1. A017GA3E01

      Disconnect the No. 2 cooling fan motor connector.

    2. Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 2 cooling fan motor connector.

      OK
      The No. 2 cooling fan rotates.

  6. Click here

    CHECK COOLING FAN ECU (POWER SOURCE)


    1. A017CQIE03

      Disconnect the cooling fan ECU connector.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      A9-3 (+B1) - A9-1 (E1) Ignition switch on (IG) 11 to 14 V

  7. Click here

    REPLACE COOLING FAN ECUClick here

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    REPLACE NO. 1 COOLING FAN MOTORClick here

  10. Click here

    REPLACE NO. 2 COOLING FAN MOTORClick here

  11. Click here

    CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)


    1. A017CQIE04

      Disconnect the cooling fan ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A9-1 (E1) - Body ground Always Below 1 Ω

  12. Click here

    INSPECT FAN MAIN RELAY


    1. A017CIR

      Remove the FAN MAIN relay from the engine room relay block and junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
      3 - 5 Apply battery voltage between terminals 1 and 2 Below 1 Ω

  13. Click here

    CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN MAIN RELAY)


    1. A017D5KE02

      Disconnect the cooling fan ECU connector.

    2. Remove the FAN MAIN relay from the engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A9-3 (+B1) - 5 (FAN MAIN relay) Always Below 1 Ω

  14. Click here

    CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - BODY GROUND)


    1. A017ENWE02

      Remove the FAN MAIN relay from the engine room relay block and junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      2 (FAN MAIN relay) - Body ground Always Below 1 Ω

  15. Click here

    CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - FAN MAIN FUSE)


    1. A017CGAE02

      Remove the FAN MAIN relay from the engine room relay block and junction block.

    2. Remove the fusible link block assembly from the engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      3 (FAN MAIN relay) - 1 (FAN MAIN fuse) Always Below 1 Ω

  16. Click here

    INSPECT FUSIBLE LINK BLOCK ASSEMBLY (FAN MAIN FUSE)


    1. A017C5IE05

      Remove the fusible link block assembly from the engine room relay block and junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      1 - 2 (FAN MAIN fuse) Always Below 1 Ω

  17. Click here

    CHECK FUSE (EFI MAIN)


    1. A017EOCE01

      Remove the EFI MAIN fuse from the engine room relay block and junction block.


      1. Measure the resistance according to the value(s) in the table below.

        Standard resistance
        Tester Connection Condition Specified Condition
        EFI MAIN fuse Always Below 1 Ω

  18. Click here

    CHECK HARNESS AND CONNECTOR (EFI MAIN FUSE - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)


    1. Remove the EFI MAIN fuse from the engine room relay block and junction block.

    2. A017D9S

      Remove the engine room junction block assembly from the engine room relay block and junction block.

    3. A017G6BE01

      Disconnect the 2E connector from the engine room junction block assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      2 (EFI MAIN fuse) - 2E-12 Always Below 1 Ω

  19. Click here

    CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)


    1. Remove the FAN MAIN relay from the engine room relay block and junction block.

    2. A017D9S

      Remove the engine room junction block assembly from the engine room relay block and junction block.

    3. A017EL1E02

      Disconnect the 2E connector from the engine room junction block assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      1 (FAN MAIN reray) - 2E-7 Always Below 1 Ω

  20. Click here

    CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND)


    1. A017BEA

      Remove the engine room junction block assembly from the engine room relay block and junction block.

    2. A017CUOE01

      Disconnect the 2D and 2E connectors from the engine room junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      2D-8 - Body ground Always Below 1 Ω
      2E-10 - Body ground Always Below 1 Ω

  21. Click here

    CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the D31 connector from the ECM.

    2. A017D9S

      Remove the engine room junction block assembly from the engine room relay block and junction block.

    3. A017G61E01

      Disconnect the 2E connector from the engine room junction block assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      D31-8 (MREL) - 2E-9 Always Below 1 Ω

  22. Click here

    INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (EFI RELAY)


    1. A017C13

      Remove the engine room junction block assembly from the engine room relay block and junction block.

    2. A017B8HE01

      Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      2E-12 - 2E-7 Battery voltage is not applied between terminals 2E-9 and 2E-10 10 kΩ or higher
      2E-12 - 2E-7 Apply battery voltage between terminals 2E-9 and 2E-10 Below 1 Ω
      Note:

      While using the battery for the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.


  23. Click here

    REPLACE ECMClick here

  24. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  25. Click here

    REPLACE FAN MAIN RELAY

  26. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  27. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  28. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  29. Click here

    REPLACE FUSIBLE LINK BLOCK ASSEMBLY

  30. Click here

    REPLACE FUSE

  31. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  32. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  33. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  34. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  35. Click here

    REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLYClick here