Click here

EXHAUST PIPE INSTALLATION

Click here
Click here
  1. Click here

    INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    1. A017CD8E01

      Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

      09224-00010
      40 N*m 408 kgf*cm 30 ft.*lbf for use with SST
      44 N*m 449 kgf*cm 32 ft.*lbf for use without SST
      Tip:

      • Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

      • Make sure that SST and the wrench are connected in a straight line.

  2. Click here

    INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A017EE5

      Install a new gasket to the front exhaust pipe assembly.

    2. Install the front exhaust pipe assembly with 2 new nuts.

      56 N*m 571 kgf*cm 41 ft.*lbf
    3. A017CJP

      Connect the heated oxygen sensor (for bank 2 sensor 2) connector.

  3. Click here

    INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    1. A017BZAE01

      Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.

      09224-00010
      40 N*m 408 kgf*cm 30 ft.*lbf for use with SST
      44 N*m 449 kgf*cm 32 ft.*lbf for use without SST
      Tip:

      • Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

      • Make sure that SST and the wrench are connected in a straight line.

  4. Click here

    INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY


    1. A017F2Y

      Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.

    2. Install the front No. 3 exhaust pipe sub-assembly with 2 new nuts and the 2 bolts.

      56 N*m 571 kgf*cm 41 ft.*lbf
    3. A017C8S

      Install the 3 clamps and connect the heated oxygen sensor (for bank 1 sensor 2) connector.

    4. A017CT1

      Tighten the front exhaust pipe assembly bolt.

      21 N*m 214 kgf*cm 15 ft.*lbf
  5. Click here

    INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. A017BDT

      Using vernier calipers, measure the free length of the compression spring.

      Minimum 41.5 mm (1.63 in.)
      Tip:

      If the length is less than the minimum, replace the compression spring.

    2. A017F8GE01

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

      Note:

      • Tap in the gasket in the correct direction.

      • Do not reuse the removed gasket.

      • Do not push in the gasket while installing the center exhaust pipe assembly.

    3. Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.

    4. A017EM8

      Install the 2 compression springs and 2 bolts.

      48 N*m 489 kgf*cm 35 ft.*lbf
  6. Click here

    INSTALL EXHAUST PIPE DAMPER


    1. A017CTV

      Install the exhaust pipe damper with the 2 bolts.

      19 N*m 194 kgf*cm 14 ft.*lbf
  7. Click here

    INSTALL TAIL EXHAUST PIPE ASSEMBLY


    1. A017BDT

      Using vernier calipers, measure the free length of the compression spring.

      Minimum 40.5 mm (1.59 in.)
      Tip:

      If the length is less than the minimum, replace the compression spring.

    2. A017F8GE01

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

      Note:

      • Tap in the gasket in the correct direction.

      • Do not reuse the removed gasket.

      • Do not push in the gasket while installing the tail exhaust pipe assembly.

    3. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

    4. A017DZ8

      Install the 2 compression springs and 2 bolts.

      48 N*m 489 kgf*cm 35 ft.*lbf
  8. Click here

    INSPECT FOR EXHAUST GAS LEAK

    If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

  9. Click here

    INSTALL NO. 2 ENGINE UNDER COVER


    1. A017CNJ

      Install the No. 2 engine under cover with the 2 bolts.

  10. Click here

    INSTALL NO. 1 ENGINE UNDER COVER


    1. A017D1W

      Install the No. 1 engine under cover with the 6 bolts and 2 clips.

  11. Click here

    INSTALL ENGINE UNDER COVER ASSEMBLY


    1. A017FXN

      Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

    2. A017FPR

      Install the engine under cover assembly RR with the 2 bolts.