FUEL SENDER GAUGE ASSEMBLY REMOVAL

DISCHARGE FUEL SYSTEM PRESSURE

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

REMOVE SEAT TRACK BRACKET COVER LH

1. 

   Disengage the 8 claws and remove the 2 rear seat track bracket covers.

REMOVE REAR OUTER TRACK BRACKET COVER LH

1. 

   Disengage the 4 claws and remove the rear outer track bracket cover.

REMOVE REAR INNER TRACK BRACKET COVER LH

1. 

   Disengage the 4 claws and remove the rear inner track bracket cover.

REMOVE REAR SEAT LEG SIDE COVER LH

1. 

   Disengage the 3 claws.

2. Disengage the clip and remove the rear seat leg side cover.

DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

1. 

   Pull down the adjuster's lock piece to release the lock as shown in the illustration.

2. 

   Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

3. 

   Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

5. 

   Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

REMOVE REAR NO. 1 SEAT ASSEMBLY LH

1. 

   Remove the 3 bolts on the rear side of the seat.

2. 

   Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

   Note:

   Be careful not to damage the vehicle body.

REMOVE SEAT TRACK BRACKET COVER RH

1. 

   Disengage the 8 claws and remove the 2 rear seat track bracket covers.

REMOVE REAR OUTER TRACK BRACKET COVER RH

1. 

   Disengage the 4 claws and remove the rear outer track bracket cover.

REMOVE REAR INNER TRACK BRACKET COVER RH

1. 

   Disengage the 4 claws and remove the rear inner track bracket cover.

REMOVE REAR SEAT LEG SIDE COVER RH

1. 

   Disengage the 3 claws.

2. Disengage the clip and remove the rear seat leg side cover.

DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

1. 

   Pull down the adjuster's lock piece to release the lock as shown in the illustration.

2. 

   Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

3. 

   Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

5. 

   Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

REMOVE REAR NO. 1 SEAT ASSEMBLY RH

1. 

   Remove the 3 bolts on the rear side of the seat.

2. 

   Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

   Note:

   Be careful not to damage the vehicle body.

REMOVE REAR DOOR SCUFF PLATE LH

1. 

   Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.

REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

1. 

   Remove the rear door opening trim weatherstrip LH.

REMOVE DECK BOARD ASSEMBLY

1. 

   Remove the deck board assembly.

REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

1. 

   Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

1. 

   Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

1. 

   Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.

REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

1. 

   Disengage the 2 clips and remove the rear seat side cover LH.

REMOVE DECK SIDE TRIM BOX LH

1. 

   Remove the 2 deck side trim clips and clip.

2. 

   Remove the deck side trim box LH as shown in the illustration.

REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

1. 

   Disengage the 2 clips and remove the rear seat side cover RH.

REMOVE JACK CARRIER CUSHION (for LHD)

1. 

   Remove the jack carrier cushion.

REMOVE JACK CARRIER CUSHION (for RHD)

1. 

   Remove the jack carrier cushion.

REMOVE JACK ASSEMBLY (for LHD)

1. 

   Remove the jack assembly.

REMOVE JACK ASSEMBLY (for RHD)

1. 

   Remove the jack assembly.

REMOVE JACK CARRIER ASSEMBLY (for LHD)

1. 

   Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

REMOVE JACK CARRIER ASSEMBLY (for RHD)

1. 

   Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

REMOVE DECK SIDE TRIM BOX RH

1. 

   Remove the 2 deck side trim clips and clip.

2. 

   Remove the deck side trim box RH as shown in the illustration.

REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

1. 

   Remove the 4 bolts and 4 nuts.

2. Remove the deck floor board assembly.

REMOVE REAR MAT

1. 

   Remove the rear mat.

REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Disengage the 3 claws.

2. Remove the 2 nuts and the deck floor board assembly.

REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

1. 

   Remove the 2 nuts and the deck floor box.

REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Remove the bolt and rear No. 2 seat inner belt assembly.

   Tip:

   Use the same procedure for the RH side and LH side.

DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

1. 

   Remove the bolt and disconnect the rear seat lap type belt assembly LH.

DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Remove the 4 bolts and the rear No. 2 seat assembly.

REMOVE REAR FLOOR FINISH PLATE

1. 

   Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.

REMOVE DECK SIDE TRIM COVER NO.2

1. 

   Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

   Tip:

   Tape the screwdriver tip before use.

REMOVE DECK SIDE TRIM LH

1. 

   Remove the bolt.

2. 

   Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.

REMOVE SIDE TRIM COVER LH

1. 

   Disengage the 10 claws and remove the side trim cover LH.

REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

1. 

   Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

   Tip:

   Tape the screwdriver tip before use.

REMOVE REAR POWER POINT SOCKET ASSEMBLY

1. Disconnect the connector.

2. 

   Disengage the claw and remove the rear power point socket assembly.

REMOVE REAR POWER OUTLET SOCKET COVER

1. 

   Disengage the 2 claws and remove the rear power outlet socket cover.

REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)

1. 

   Disengage the 10 claws and remove the rear deck trim cover.

REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

1. 

   Disengage the 5 claws and remove the reclining remote control bezel LH.

REMOVE ROPE HOOK ASSEMBLY (for LH Side)

1. 

   for Front Side:

   
   

   1. Using a screwdriver, disengage the 2 claws.

      Tip:

      Tape the screwdriver tip before use.

   2. Remove the bolt and the rope hook assembly.

2. 

   for Rear Side:

   
   

   1. Using a screwdriver, disengage the 2 claws.

      Tip:

      Tape the screwdriver tip before use.

   2. Remove the bolt and rope hook assembly.

REMOVE NO. 2 DECK SIDE TRIM HOOK

1. 

   Remove the screw and the No. 2 deck side trim hook.

REMOVE FRONT DECK SIDE TRIM COVER LH

1. 

   Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

   Tip:

   Tape the screwdriver tip before use.

DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

1. 

   Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

1. Remove the 2 bolts.

2. Remove the 2 clips.

3. 

   Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

REMOVE REAR FLOOR SERVICE HOLE COVER

1. Lift up the front floor carpet.

   
   
   1. 

      Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)

   2. 

      Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)

2. 

   Remove the rear floor service hole cover.

3. Disconnect the fuel pump connector.

REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

1. 

   Remove the tube joint clip, and pull out the fuel pump tube.

   Note:
   

   • Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.

   • It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.

   • Disconnect the quick connector by hand. Do not use any tools

   • Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.

   • If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.

2. 

   Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.

   09808-14020

   09808-01410

   09808-01420

   09808-01430

   Tip:
   

   • Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.

   • Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

3. 

   Using SST, loosen the fuel pump gauge retainer.

   09808-14020

   09808-01410

   09808-01420

   09808-01430

   Note:
   

   • Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.

   • Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.

   Tip:

   The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

4. Remove the fuel pump gauge retainer.

5. 

   Remove the fuel suction tube with pump and gauge.

   Note:

   Be careful not to bend the arm of the fuel sender gauge.

6. Remove the gasket from the fuel tank.