FUEL PUMP REMOVAL


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Tech Tips

    Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR CENTER SEAT ASSEMBLY

  4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

  5. REMOVE SEAT TRACK BRACKET COVER LH


    1. A017DZY

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  6. REMOVE REAR OUTER TRACK BRACKET COVER LH


    1. A017BNT

      Disengage the 4 claws and remove the rear outer track bracket cover.

  7. REMOVE REAR INNER TRACK BRACKET COVER LH


    1. A017FUU

      Disengage the 4 claws and remove the rear inner track bracket cover.

  8. REMOVE REAR SEAT LEG SIDE COVER LH


    1. A017BXU

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A017BM1E01
    2. A017BWQE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A017BFVE01

    4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

      A017FFKE01

    6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

  10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. A017BHD

      Remove the 3 bolts on the rear side of the seat.

    2. A017FCR

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note

      Be careful not to damage the vehicle body.

  11. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

  12. REMOVE SEAT TRACK BRACKET COVER RH


    1. A017ERX

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  13. REMOVE REAR OUTER TRACK BRACKET COVER RH


    1. A017D2L

      Disengage the 4 claws and remove the rear outer track bracket cover.

  14. REMOVE REAR INNER TRACK BRACKET COVER RH


    1. A017F59

      Disengage the 4 claws and remove the rear inner track bracket cover.

  15. REMOVE REAR SEAT LEG SIDE COVER RH


    1. A017F28

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  16. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A017B3FE01
    2. A017D49E01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A017BJPE01

    4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

      A017D3BE01

    6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

  17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH


    1. A017EZ3

      Remove the 3 bolts on the rear side of the seat.

    2. A017D5O

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note

      Be careful not to damage the vehicle body.

  18. REMOVE REAR DOOR SCUFF PLATE LH


    1. A017D4T

      Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017C1V

      Remove the rear door opening trim weatherstrip LH.

  20. REMOVE DECK BOARD ASSEMBLY


    1. A017CPI

      Remove the deck board assembly.

  21. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  22. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  23. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

  24. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.

  25. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Disengage the 2 clips and remove the rear seat side cover LH.

  26. REMOVE DECK SIDE TRIM BOX LH


    1. A017BZVE01

      Remove the 2 deck side trim clips and clip.

    2. Remove the deck side trim box LH as shown in the illustration.

      A017G2A

  27. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Disengage the 2 clips and remove the rear seat side cover RH.

  28. REMOVE JACK CARRIER SUPPORT

  29. REMOVE JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Remove the jack carrier cushion.

  30. REMOVE JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Remove the jack carrier cushion.

  31. REMOVE JACK ASSEMBLY (for LHD)


    1. A017EKS

      Remove the jack assembly.

  32. REMOVE JACK ASSEMBLY (for RHD)


    1. A017DSX

      Remove the jack assembly.

  33. REMOVE JACK CARRIER ASSEMBLY (for LHD)


    1. A017EAS

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  34. REMOVE JACK CARRIER ASSEMBLY (for RHD)


    1. A017D6R

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  35. REMOVE DECK SIDE TRIM BOX RH


    1. A017FOPE01

      Remove the 2 deck side trim clips and clip.

    2. Remove the deck side trim box RH as shown in the illustration.

      A017E9B

  36. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017G15

      Remove the 4 bolts and 4 nuts.

    2. Remove the deck floor board assembly.

  37. REMOVE REAR MAT


    1. A017F51

      Remove the rear mat.

  38. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017FMA

      Disengage the 3 claws.

    2. Remove the 2 nuts and the deck floor board assembly.

  39. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Remove the 2 nuts and the deck floor box.

  40. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Remove the bolt and rear No. 2 seat inner belt assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  41. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Remove the bolt and disconnect the rear seat lap type belt assembly LH.

  42. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  43. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Remove the 4 bolts and the rear No. 2 seat assembly.

  44. REMOVE REAR FLOOR FINISH PLATE


    1. A017BSY

      Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.

  45. REMOVE DECK SIDE TRIM COVER NO.2


    1. A017FRQE01

      Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  46. REMOVE DECK SIDE TRIM LH


    1. A017F36

      Remove the bolt.

    2. A017B91

      Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.

  47. REMOVE SIDE TRIM COVER LH


    1. A017EO1

      Disengage the 10 claws and remove the side trim cover LH.

  48. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017EUZE01

      Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  49. REMOVE REAR POWER POINT SOCKET ASSEMBLY


    1. Disconnect the connector.

    2. A017G8M

      Disengage the claw and remove the rear power point socket assembly.

  50. REMOVE REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Disengage the 2 claws and remove the rear power outlet socket cover.

  51. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Disengage the 10 claws and remove the rear deck trim cover.

  52. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Disengage the 5 claws and remove the reclining remote control bezel LH.

  53. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    1. A017FLCE01

      for Front Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Remove the bolt and the rope hook assembly.

    2. A017B9EE01

      for Rear Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Remove the bolt and rope hook assembly.

  54. REMOVE NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Remove the screw and the No. 2 deck side trim hook.

  55. REMOVE FRONT DECK SIDE TRIM COVER LH


    1. A017C3ZE01

      Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

      Tech Tips

      Tape the screwdriver tip before use.

  56. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. A017ETD

      Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

  57. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 bolts.

    2. Remove the 2 clips.

    3. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

      A017FE0

  58. REMOVE REAR FLOOR SERVICE HOLE COVER


    1. Lift up the front floor carpet.


      1. A017C85

        Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)

      2. A017EIU

        Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)

    2. A017B8R

      Remove the rear floor service hole cover.

    3. Disconnect the fuel pump connector.

  59. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    1. A017E74E01

      Remove the tube joint clip, and pull out the fuel pump tube.

      Note


      • Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.

      • It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.

      • Disconnect the quick connector by hand. Do not use any tools

      • Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.

      • If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.

    2. A017BU2E01

      Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.

      SST
      09808-14020   ( 09808-01410, 09808-01420, 09808-01430 )

      Tech Tips


      • Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.

      • Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

    3. A017DQT

      Using SST, loosen the fuel pump gauge retainer.

      SST
      09808-14020   ( 09808-01410, 09808-01420, 09808-01430 )

      Note


      • Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.

      • Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.

      Tech Tips

      The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

    4. Remove the fuel pump gauge retainer.

    5. A017EWRE01

      Remove the fuel suction tube with pump and gauge.

      Note

      Be careful not to bend the arm of the fuel sender gauge.

    6. Remove the gasket from the fuel tank.