DRIVE BELT INSTALLATION


  1. INSTALL V-RIBBED BELT


    1. A017F8UE01

      Install the V-ribbed belt.

    2. Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.

      SST
      09961-00950
    3. A017CTEE01

      If it is difficult to install the V-ribbed belt, perform the following procedure:


      1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

      2. Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed belt tensioner assembly pulley.

        Note


        • Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.

        • Check that the V-ribbed belt is properly set to each pulley.

      3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the V-ribbed belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.

  2. INSTALL FRONT FENDER APRON SEAL RH


    1. A017FOB

      Install the front fender apron seal RH with the 2 bolts and clip.

  3. INSTALL FRONT FENDER LINER RH


    1. A017B8K

      Install the front fender liner RH with the 5 clips and 7 screws.

    2. A017EB7

      Install 2 new grommets.

    3. Using a 4 mm hexagon wrench, install the 2 screws.

    4. A017EMR

      Install the screw and pin hold clip.

      Torque:
      3.0 N*m  { 31 kgf*cm, 27 in.*lbf }

  4. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the front fender side protector from the vehicle body.

      3. Wipe off any tape adhesive residue with cleaner.

    2. A017BL5

      Clean the front fender moulding sub-assembly RH. (If reusing the front fender moulding sub-assembly RH)


      1. Using a heat light, heat the front fender moulding sub-assembly RH.

      2. Remove the front fender side protector from the front fender moulding sub-assembly RH.

      3. Wipe off any tape adhesive residue with cleaner.

      4. Install a new front fender side protector to the the front fender moulding sub-assembly RH.

    3. A017BNI

      Install the front fender moulding sub-assembly RH.


      1. Using a heat light, heat the vehicle body and the front fender moulding sub-assembly RH.

      2. Remove the release paper from the front fender moulding sub-assembly RH.

        Tech Tips

        After removing the release paper, keep the exposed adhesive free from foreign matter.

      3. Engage the 3 clips and install the front fender moulding sub-assembly RH.

    4. A017EVY

      Using a 4 mm hexagon wrench, install the screw.

    5. Install the clip.

  5. INSTALL NO. 1 ENGINE UNDER COVER


    1. A017B8T

      Install the No. 1 engine under cover with the 6 bolts and 2 clips.

  6. INSTALL ENGINE UNDER COVER ASSEMBLY


    1. A017FXN

      Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

    2. A017FPR

      Install the engine under cover assembly RR with the 2 bolts.

  7. INSTALL FRONT WHEEL RH

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }