HEATED OXYGEN SENSOR INSTALLATION


  1. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    1. A017BZAE01

      Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.

      SST
      09224-00010
      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf, for use with SST }
      44 N*m  { 449 kgf*cm, 32 ft.*lbf, for use without SST }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

      • Make sure that SST and the wrench are connected in a straight line.

  2. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    1. A017CD8E01

      Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.

      SST
      09224-00010
      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf, for use with SST }
      44 N*m  { 449 kgf*cm, 32 ft.*lbf, for use without SST }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

      • Make sure that SST and the wrench are connected in a straight line.

  3. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A017EE5

      Install a new gasket to the front exhaust pipe assembly.

    2. Install the front exhaust pipe assembly with 2 new nuts.

      Torque:
      56 N*m  { 571 kgf*cm, 41 ft.*lbf }
    3. A017CJP

      Connect the heated oxygen sensor (for bank 2 sensor 2) connector.

  4. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY


    1. A017F2Y

      Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.

    2. Install the front No. 3 exhaust pipe sub-assembly with 2 new nuts and the 2 bolts.

      Torque:
      56 N*m  { 571 kgf*cm, 41 ft.*lbf }
    3. A017C8S

      Install the 3 clamps and connect the heated oxygen sensor (for bank 1 sensor 2) connector.

    4. A017CT1

      Tighten the front exhaust pipe assembly bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  5. INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. A017BDT

      Using vernier calipers, measure the free length of the compression spring.

      Minimum 41.5 mm (1.63 in.)

      Tech Tips

      If the length is less than the minimum, replace the compression spring.

    2. A017F8GE01

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

      Note


      • Tap in the gasket in the correct direction.

      • Do not reuse the removed gasket.

      • Do not push in the gasket while installing the center exhaust pipe assembly.

    3. Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.

    4. A017EM8

      Install the 2 compression springs and 2 bolts.

      Torque:
      48 N*m  { 489 kgf*cm, 35 ft.*lbf }

  6. INSTALL TAIL EXHAUST PIPE ASSEMBLY


    1. A017BDT

      Using vernier calipers, measure the free length of the compression spring.

      Minimum 40.5 mm (1.59 in.)

      Tech Tips

      If the length is less than the minimum, replace the compression spring.

    2. A017F8GE01

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

      Note


      • Tap in the gasket in the correct direction.

      • Do not reuse the removed gasket.

      • Do not push in the gasket while installing the tail exhaust pipe assembly.

    3. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

    4. A017DZ8

      Install the 2 compression springs and 2 bolts.

      Torque:
      48 N*m  { 489 kgf*cm, 35 ft.*lbf }

  7. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)


    1. A017FC7E01

      Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.

    2. A017G8QE01

      Remove SST from the transaxle.

    3. Insert the yoke into the transaxle.

    4. A017G71

      Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.

    5. A017FC7E01

      Tighten the 4 bolts.

      Torque:
      74 N*m  { 750 kgf*cm, 54 ft.*lbf }

  8. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)


    1. A017B7D

      Remove the piece of cloth from the joint.

    2. Using a hexagon wrench (6 mm), tighten the 6 bolts.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }
    3. A017BGHE01

      With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.

      (A)
      58.0 +/- 0.5 mm (2.283 +/- 0.02 in.)

    4. Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.

      A017FFHE01
      Torque:
      37 N*m  { 375 kgf*cm, 27 ft.*lbf }
      (B)
      12.5 +/- 1.0 mm (0.492 +/- 0.039 in.)

    5. Check that the center line of the bracket is at the right angle in the shaft axial direction.

    6. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.


      1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

      2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

      3. Remove the transfer dynamic damper.

      4. Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).

        SST
        09370-50010
        No. 1 joint angle
        (A) - (B) = -1.3° to -3.3°

      5. Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

        SST
        09370-50010
        No. 2 joint angle
        (C) - (D) = 1.8° to 3.5°
        A017CTPE01

        Tech Tips

        If the measured angle is not within the specification, adjust it with the center support bearing adjusting shim.

        Center support bearing adjusting shim thickness
        Thickness mm (in.) Thickness mm (in.)
        3.2 (0.126) 11.0 (0.433)
        4.5 (0.177) 13.5 (0.531)
        6.5 (0.256) 15.5 (0.610)
        9.0 (0.354) 17.5 (0.689)

      6. Install the transfer dynamic damper.

        Torque:
        26 N*m  { 265 kgf*cm, 19 ft.*lbf }

  9. INSPECT FOR EXHAUST GAS LEAK

    If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

  10. INSPECT AND ADJUST TRANSFER OIL (for 4WD)

    Tech Tips

    Click here

  11. INSTALL FRONT FLOOR COVER LH


    1. A017BWS

      Install the 3 clamps, 6 bolts and the front floor cover LH.

  12. INSTALL NO. 2 ENGINE UNDER COVER


    1. A017CNJ

      Install the No. 2 engine under cover with the 2 bolts.

  13. INSTALL NO. 1 ENGINE UNDER COVER


    1. A017D1W

      Install the No. 1 engine under cover with the 6 bolts and 2 clips.

  14. INSTALL ENGINE UNDER COVER ASSEMBLY


    1. A017FXN

      Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

    2. A017FPR

      Install the engine under cover assembly RR with the 2 bolts.