Click here

AIR FUEL RATIO SENSOR REMOVAL

Click here
Click here
  1. Click here

    REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    1. A017BMP

      Disconnect the air fuel ratio sensor connector and remove the clamp.

    2. A017CEN

      Using SST, remove the sensor from the exhaust manifold sub-assembly LH.

      09224-00010
  2. Click here

    REMOVE ENGINE UNDER COVER ASSEMBLY


    1. A017FPR

      Remove the 2 bolts and engine under cover assembly RR.

    2. A017FXN

      Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.

  3. Click here

    REMOVE NO. 1 ENGINE UNDER COVER


    1. A017D1W

      Remove the 6 bolts, 2 clips and No. 1 engine under cover.

  4. Click here

    REMOVE NO. 2 ENGINE UNDER COVER


    1. A017CNJ

      Remove the 2 bolts and No. 2 engine under cover.

  5. Click here

    REMOVE FRONT FLOOR COVER LH


    1. A017BWS

      Remove the 3 clamps, 6 bolts and front floor cover LH.

  6. Click here

    REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)


    1. A017FGM

      Depress the brake pedal and hold it.

    2. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

      Tip:

      Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

    3. A017FC7E01

      Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

    4. Remove the 4 nuts, 4 bolts and 4 washers.

    5. A017G71

      Remove the 4 bolts and 4 adjusting shims.

    6. A017DKO

      Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

    7. A017G8QE01

      Insert SST into the transfer to prevent oil leakage.

      09325-20010
  7. Click here

    REMOVE TAIL EXHAUST PIPE ASSEMBLY


    1. A017DZ8

      Remove the 2 bolts and 2 compression springs.

    2. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

    3. Remove the gasket from the center exhaust pipe assembly.

  8. Click here

    REMOVE CENTER EXHAUST PIPE ASSEMBLY


    1. A017EM8

      Remove the 2 bolts and 2 compression springs.

    2. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

    3. Remove the gasket from the No. 3 exhaust pipe sub-assembly.

  9. Click here

    REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY


    1. A017C8S

      Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.

    2. A017F2Y

      Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

    3. Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.

  10. Click here

    REMOVE MANIFOLD STAY


    1. A017DFR

      Remove the bolt, nut and manifold stay.

  11. Click here

    REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    1. A017FX3

      Disconnect the air fuel ratio sensor (for bank 1 sensor 1) connector and remove the clamp.

    2. A017D7L

      Remove the 6 nuts and exhaust manifold sub-assembly RH.

    3. Remove the gasket.

  12. Click here

    REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    1. A017CYHE01

      Using SST, remove the air fuel ratio sensor from the exhaust manifold sub-assembly RH.

      09224-00010