ACTIVE CONTROL ENGINE MOUNT REMOVAL


  1. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A017EFM

      Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.

  2. REMOVE ENGINE UNDER COVER ASSEMBLY


    1. A017FPR

      Remove the 2 bolts and engine under cover assembly RR.

    2. A017FXN

      Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.

  3. REMOVE NO. 1 ENGINE UNDER COVER


    1. A017B8T

      Remove the 6 bolts, 2 clips and No. 1 engine under cover.

  4. DRAIN ENGINE COOLANT


    1. Loosen the radiator drain cock plug.

      A017CW8E01

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. Remove the radiator cap sub-assembly from the radiator assembly.

      Note

      Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    3. Loosen the 2 cylinder block drain cock plugs.

  5. REMOVE COOL AIR INTAKE DUCT SEAL


    1. A017CN1

      Remove the 11 clips and cool air intake duct seal.

  6. REMOVE BATTERY

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    1. A017FMC

      Loosen the nut, and disconnect the negative battery terminal.

    2. Loosen the nut, and disconnect the positive battery terminal.

    3. Loosen the nut, and remove the bolt and battery clamp.

    4. Remove the battery and battery tray.

  7. REMOVE NO. 2 AIR CLEANER INLET


    1. A017D82

      Disconnect the 2 vacuum switching valve clamps.

    2. Disconnect the 2 vacuum hoses.

    3. Remove the 2 bolts and No. 2 air cleaner inlet.

  8. REMOVE NO. 1 AIR CLEANER INLET


    1. A017C2Q

      Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.

  9. DISCONNECT NO. 1 RADIATOR HOSE


    1. A017EYO

      Disconnect the No. 1 radiator hose from the radiator.

  10. DISCONNECT NO. 2 RADIATOR HOSE


    1. A017FFS

      Disconnect the No. 2 radiator hose from the radiator.

  11. DISCONNECT OIL COOLER HOSE


    1. A017F5B

      Disconnect the oil cooler hoses from the radiator.

  12. DISCONNECT COOLING FAN ECU CONNECTOR


    1. A017FVV

      Detach the wire harness clamps from the fan shroud LH side.

    2. A017DKS

      Detach the wire harness clamps from the fan shroud RH side and disconnect the cooling fan ECU connector.

  13. REMOVE RADIATOR GRILLE


    1. A017GBWE01

      Put protective tape around the radiator grille.

    2. A017DWF

      Remove the 2 bolts and 4 clips.

    3. A017G18

      Disengage the 6 claws and 4 guides, and remove the radiator grille.

  14. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)


    1. A017D3E

      Remove the hood lock nut cap.

    2. A017CPZ

      Remove the 3 bolts.

    3. A017DBV

      Disconnect the hood lock control cable and remove the hood lock assembly.

  15. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)


    1. A017EVU

      Disconnect the connector.

    2. A017FVJ

      Remove the hood lock nut cap.

    3. A017CI6

      Remove the 3 bolts.

    4. A017BQ6

      Disconnect the hood lock control cable and remove the hood lock assembly.

  16. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for LHD)


    1. A017FE9

      Disconnect the low pitched horn and high pitched horn connectors.

    2. A017E8C

      Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.

  17. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for RHD)


    1. A017FE9

      Disconnect the low pitched horn and high pitched horn connectors.

    2. A017C96

      Detach the hood lock control cable clamp and remove the 6 bolts and upper radiator support sub-assembly.

  18. SEPARATE COOLER CONDENSER ASSEMBLY


    1. A017CEX

      Remove the 4 bolts and move the cooler condenser assembly to remove the radiator assembly and fan assembly with motor.

  19. REMOVE RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR


    1. A017G1R

      Remove the radiator assembly and fan assembly with motor.

  20. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET

    Tech Tips

    Securely support the automatic transaxle using a jack.


    1. A017CPG

      Remove the nut, 3 bolts and the transverse engine mounting bracket.

  21. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY


    1. A017EQL

      Disconnect the vacuum hose sub-assembly from the air cleaner cap sub-assembly and vacuum switching valve.

    2. A017EW3

      Remove the 2 clamps.

    3. A017BZ6

      Disconnect the duty vacuum switching valve connector and clamp.

    4. A017DL3E01

      Remove the hole plug, 3 nuts and front engine mounting insulator assembly.