THROTTLE BODY INSTALLATION


  1. INSTALL THROTTLE BODY


    1. A017F2JE01

      Install a new throttle body gasket to the intake air surge tank assembly.

    2. A017BQ2

      Install the throttle body with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    3. A017BCR

      Connect the 2 water by-pass hoses.

    4. A017DHZ

      Connect the throttle body connector and clamp.

  2. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. A017DHBE01

      Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

      Tech Tips


      • A = 30°

      • B = 11 to 14 mm (0.433 in. to 0.551 in.)

    2. Install the air cleaner cap with the 2 bolts and clips.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    3. A017BB9

      Connect the 3 vacuum hoses.

    4. A017EEU

      Connect the mass air flow meter connector.

    5. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.

  3. ADD ENGINE COOLANT


    1. Tighten the radiator drain cock plug by hand.

    2. Tighten the cylinder block drain cock plug. (for Bank 1)

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    3. Tighten the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    4. Loosen the air drain cock plug on the water inlet housing.

    5. A017G9AE03
      Text in Illustration
      *1 Air Drain Plug

      Loosen the air drain plug at the top of the radiator assembly 3 or 4 turns.

    6. Add engine coolant to the radiator inlet opening until engine coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    7. Continue to add engine coolant to the radiator inlet opening until engine coolant overflows from the radiator air drain hole. Then tighten the air drain plug.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

      Tech Tips

      If the engine coolant level at the radiator inlet opening drops after squeezing the No. 1 radiator hose and No. 2 radiator hose, add engine coolant.

    8. Slowly fill the radiator assembly with engine coolant.

      Standard Capacity
      Condition Specified Condition
      w/ Rear Heater 11.7 liters (12.4 US qts, 10.3 Imp. qts)
      w/o Rear Heater 9.5 liters (10.1 US qts, 8.4 Imp. qts)

      Note

      Never use water as a substitute for engine coolant.

      Tech Tips

      TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

    9. Slowly pour engine coolant into the radiator reservoir tank until it reaches the full line.

    10. Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

      If the engine coolant level is low, add engine coolant.

    11. Bleed air from the cooling system.


      1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

        Tech Tips

        The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.

      2. Maintain the engine speed at 2500 to 3000 rpm.

      3. Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air.

        CAUTION:

        When squeezing the No. 1 radiator hose and No. 2 radiator hose:


        • Wear protective gloves.

        • Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.

        • Keep your hands away from the fan and No. 2 fan.

        Note


        • If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

        • Make sure that the radiator reservoir tank still has some engine coolant in it.

        • If the radiator reservoir tank does not have enough engine coolant, the engine may overheat or be seriously damaged.

        • If the radiator reservoir tank does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the radiator reservoir tank is filled to the full line.

    12. Stop the engine, and wait until the engine coolant cools down.

    13. Add engine coolant to the full line on the radiator reservoir tank.

  4. INSPECT FOR COOLANT LEAK

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    Note

    Before performing each inspection, turn the A/C switch off.


    1. A017G83

      Fill the radiator with coolant and attach a radiator cap tester.

    2. Warm up the engine.

    3. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.

      If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  5. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    1. A017F9GE01

      Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

      Torque:
      Nut A
      85 N*m  { 866 kgf*cm, 63 ft.*lbf }
      Bolt B
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }
      Nut C
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }
    2. A017G69

      Engage the 4 clamps.

  6. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A017FR2

      Install the windshield wiper motor and link assembly with the 4 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Connect the connector.

  7. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. Engage the 20 claws.

      A017F5J

    2. Install the cowl top ventilator louver sub-assembly with the 2 clips.

    3. A017EML

      Engage the 2 claws and connect the front fender to cowl side seal LH.

    4. A017F5E

      Engage the 2 claws and connect the front fender to cowl side seal RH.

  8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. When reinstalling:


      1. A017C5CE01

        Clean the wiper arm serrations.

      2. Clean the wiper pivot serrations with a wire brush.

    3. A017D7ZE01

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

      Tech Tips

      Hold the wiper arm by hand when tightening the nut.

      Area Measurement
      A 25.6 mm (1.00 in.)

  9. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. When reinstalling:


      1. A017C5CE01

        Clean the wiper arm serrations.

      2. Clean the wiper pivot serrations with a wire brush.

    3. A017D4VE01

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

      Tech Tips

      Hold the wiper arm by hand when tightening the nut.

      Area Measurement
      A 31.9 mm (1.26 in.)

    4. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  10. INSTALL V-BANK COVER SUB-ASSEMBLY


    1. A017EFM

      Fit the 3 retainers and install the V-bank cover.

  11. INSTALL NO. 1 ENGINE UNDER COVER


    1. A017D1W

      Install the No. 1 engine under cover with the 6 bolts and 2 clips.

  12. INSTALL ENGINE UNDER COVER ASSEMBLY


    1. A017FXN

      Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

    2. A017FPR

      Install the engine under cover assembly RR with the 2 bolts.