THROTTLE BODY REMOVAL


  1. REMOVE ENGINE UNDER COVER ASSEMBLY


    1. A017FPR

      Remove the 2 bolts and engine under cover assembly RR.

    2. A017FXN

      Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.

  2. REMOVE NO. 1 ENGINE UNDER COVER


    1. A017B8T

      Remove the 6 bolts, 2 clips and No. 1 engine under cover.

  3. DRAIN ENGINE COOLANT


    1. Loosen the radiator drain cock plug.

      A017CW8E01

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. Remove the radiator cap sub-assembly from the radiator assembly.

      Note

      Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    3. Loosen the 2 cylinder block drain cock plugs.

  4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A017BZJ

      Remove the nut, and the front wiper arm and blade assembly LH.

  5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A017DLO

      Remove the nut, and the front wiper arm and blade assembly RH.

  6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A017EML

      Disengage the 2 claws and disconnect the front fender to cowl side seal LH.

    2. A017F5E

      Disengage the 2 claws and disconnect the front fender to cowl side seal RH.

    3. Remove the 2 clips.

      A017F5J

    4. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.

  7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A017FR2

      Disconnect the connector.

    2. Remove the 4 bolts, and the windshield wiper motor and link assembly.

  8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    1. A017G69

      Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.

    2. A017F9G

      Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.

  9. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A017EFM

      Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.

  10. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A017BB9

      Disconnect the 3 vacuum hoses.

    2. A017EZ4

      Loosen the No. 1 air cleaner hose clamp.

    3. Disconnect the hose clamps and No. 2 ventilation hose.

    4. Disconnect the mass air flow meter connector.

    5. A017FXX

      Release the 2 clips, and remove the 2 bolts.

    6. Remove the air cleaner cap sub-assembly and air cleaner filter element.

  11. REMOVE THROTTLE BODY


    1. A017DHZ

      Disconnect the throttle body connector and clamp.

    2. A017BCR

      Disconnect the 2 water by-pass hoses from the throttle body.

    3. A017BQ2

      Remove the 4 bolts and throttle body.

    4. A017F2JE01

      Remove the throttle body gasket from the intake air surge tank assembly.