REAR BLOWER MOTOR INSTALLATION


  1. INSTALL REAR BLOWER MOTOR SUB-ASSEMBLY


    1. A017ET4

      Install the rear blower motor sub-assembly with the 3 screws.

    2. Connect the connector.

  2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly RH with the 3 bolts.

      A017FTC

  4. INSTALL FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

  6. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  7. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    1. A017DDV

      Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

  8. INSTALL SIDE TRIM COVER RH (for Manual Air Conditioning System)


    1. A017CSI

      Engage the 4 claws, and install the side trim cover RH.

  9. INSTALL REAR ROOM TEMPERATURE SENSOR (for Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017B3P

      Engage the 4 claws and install the rear room temperature sensor.

  10. INSTALL DECK SIDE TRIM RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  11. INSTALL DECK SIDE TRIM COVER NO.1

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  12. INSTALL REAR SEAT SIDE GARNISH CAP


    1. A017ER4

      Engage the guide and the 6 claws.

    2. Install the rear seat side garnish cap with the screw.

  13. INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and the 4 claws, and install the rear floor finish plate.

  14. INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. A017E5S

      Install the rear No. 2 seat assembly with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  15. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH


    1. A017F2F

      Install the rear seat lap type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  16. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH


    1. Install the rear seat lap type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  17. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY


    1. A017GAE

      Install the rear No. 2 seat inner belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  18. INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  19. INSTALL DECK FLOOR BOARD ASSEMBLY


    1. A017G15

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  20. INSTALL DECK SIDE TRIM BOX LH


    1. Install the deck side trim box LH as shown in the illustration.

      A017CIY
    2. A017BZVE01

      Install the 2 deck side trim clips and the clip.

  21. INSTALL REAR SEAT SIDE COVER LH


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  22. INSTALL DECK SIDE TRIM BOX RH


    1. Install the deck side trim box RH as shown in the illustration.

      A017EFK
    2. A017FOPE01

      Install the 2 deck side trim clips and the clip.

  23. INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  24. INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  25. INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  26. INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  27. INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  28. INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  29. INSTALL JACK CARRIER SUPPORT

  30. INSTALL REAR SEAT SIDE COVER RH


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  31. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  32. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  33. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  34. INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.

  35. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A017FFPE01

      Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  36. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.