Click here

REAR BLOWER MOTOR INSTALLATION

Click here
Click here
  1. Click here

    INSTALL REAR BLOWER MOTOR SUB-ASSEMBLY


    1. A017ET4

      Install the rear blower motor sub-assembly with the 3 screws.

    2. Connect the connector.

  2. Click here

    INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure for the RH side and the LH side.

  3. Click here

    INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. A017FTC

      Install the deck trim side panel assembly RH with the 3 bolts.

  4. Click here

    INSTALL FRONT DECK SIDE TRIM COVER RH

    Tip:

    Use the same procedure for the RH side and the LH side.

  5. Click here

    INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tip:

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

  6. Click here

    INSTALL ROPE HOOK ASSEMBLY (for RH Side)

    Tip:

    Use the same procedure for the RH side and the LH side.

  7. Click here

    INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    1. A017DDV

      Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

  8. Click here

    INSTALL SIDE TRIM COVER RH (for Manual Air Conditioning System)


    1. A017CSI

      Engage the 4 claws, and install the side trim cover RH.

  9. Click here

    INSTALL REAR ROOM TEMPERATURE SENSOR (for Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017B3P

      Engage the 4 claws and install the rear room temperature sensor.

  10. Click here

    INSTALL DECK SIDE TRIM RH

    Tip:

    Use the same procedure for the RH side and the LH side.

  11. Click here

    INSTALL DECK SIDE TRIM COVER NO.1

    Tip:

    Use the same procedure for the RH side and the LH side.

  12. Click here

    INSTALL REAR SEAT SIDE GARNISH CAP


    1. A017ER4

      Engage the guide and the 6 claws.

    2. Install the rear seat side garnish cap with the screw.

  13. Click here

    INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and the 4 claws, and install the rear floor finish plate.

  14. Click here

    INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. A017E5S

      Install the rear No. 2 seat assembly with the 4 bolts.

      37 N*m 377 kgf*cm 27 ft.*lbf
  15. Click here

    CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH


    1. A017F2F

      Install the rear seat lap type belt assembly LH with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      After installing the belt, check that it is not twisted.

  16. Click here

    CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH


    1. Install the rear seat lap type belt assembly RH with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      After installing the belt, check that it is not twisted.

  17. Click here

    INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY


    1. A017GAE

      Install the rear No. 2 seat inner belt assembly with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

      Tip:

      Use the same procedure for the RH side and LH side.

  18. Click here

    INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  19. Click here

    INSTALL DECK FLOOR BOARD ASSEMBLY


    1. A017G15

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  20. Click here

    INSTALL DECK SIDE TRIM BOX LH


    1. A017CIY

      Install the deck side trim box LH as shown in the illustration.

    2. A017BZVE01

      Install the 2 deck side trim clips and the clip.

  21. Click here

    INSTALL REAR SEAT SIDE COVER LH


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  22. Click here

    INSTALL DECK SIDE TRIM BOX RH


    1. A017EFK

      Install the deck side trim box RH as shown in the illustration.

    2. A017FOPE01

      Install the 2 deck side trim clips and the clip.

  23. Click here

    INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  24. Click here

    INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  25. Click here

    INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  26. Click here

    INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  27. Click here

    INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  28. Click here

    INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  29. Click here

    INSTALL JACK CARRIER SUPPORT

  30. Click here

    INSTALL REAR SEAT SIDE COVER RH


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  31. Click here

    INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  32. Click here

    INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  33. Click here

    INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  34. Click here

    INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.

  35. Click here

    INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A017FFPE01

      Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note:

      After installation, check that the corners fit correctly.

  36. Click here

    INSTALL REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure for the RH side and the LH side.