POWER STEERING ECU INSTALLATION


  1. INSTALL POWER STEERING ECU ASSEMBLY (for LHD)


    1. A017FRG

      Install the power steering ECU assembly with the 3 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    2. A017C2SE01

      Check that the connector lever is at the fully unlocked position before installation.

      Note

      If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.

    3. A017FWJE01

      Connect the 4 connectors to the power steering ECU assembly.

    4. Lightly pull on the connector and check that the connector does not disconnect.

  2. INSTALL POWER STEERING ECU ASSEMBLY (for RHD)


    1. A017CHK

      Install the power steering ECU assembly with the 3 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }
    2. A017CK5E01

      Check that the connector lever is at the fully unlocked position before installation.

      Note

      If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.

    3. A017CK4E01

      Connect the 4 connectors to the power steering ECU assembly.

    4. Lightly pull on the connector and check that the connector will not be disconnected.

    5. Install the wire harness clamp to the power steering ECU assembly.

  3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)


    1. Connect the connectors to the back of the instrument panel junction block assembly.

    2. A017BKC

      Engage the wire harness clamp onto the instrument panel junction block assembly.

    3. A017D3T

      Install the instrument panel junction block assembly with the 3 nuts.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

    4. Connect the connectors to the instrument panel junction block assembly.

    5. Engage the wire harness clamp onto the instrument panel junction block assembly.

  4. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for LHD)


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017F8J

      Install the DLC3 to the driver side knee airbag assembly with the 2 claws.

    4. A017EBJ

      Connect the connector to the driver side knee airbag assembly.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    5. A017EHS

      Support the driver side knee airbag assembly with one hand as shown in the illustration.

    6. A017CTB

      Temporarily install the driver side knee airbag assembly with the 2 hooks.

    7. A017FEG

      Install the driver side knee airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  5. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    1. A017BY3

      Connect the hood lock control cable assembly.

    2. Connect each connector.

    3. Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    1. A017CWD

      Connect the hood lock control cable assembly.

    2. Connect each connector and the aspirator duct.

    3. A017EU2

      Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  7. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Engage the claw and clip, install the cowl side trim sub-assembly LH.

    2. Install the clip.

  8. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Engage the guide and the 8 claws, and install the front door scuff plate LH.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSPECT SRS WARNING LIGHT (for LHD)

    Tech Tips

    Click here.