Click here

PARKING BRAKE ASSEMBLY DISASSEMBLY

Click here
Click here
Tip:

  • Use the same procedures for the RH side and the LH side.

  • The procedures listed below are for the LH side.

Click here
  1. Click here

    REMOVE REAR WHEEL

  2. Click here

    REMOVE REAR AXLE SHAFT NUT (for 4WD)

    Note:

    Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    Tip:

    Click here.

  3. Click here

    SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)


    1. A017FLR

      Remove the 2 bolts and separate the rear disc brake caliper assembly.

      Note:

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  4. Click here

    SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)


    1. A017DLS

      Remove the 2 bolts and separate the rear disc brake caliper assembly.

      Note:

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  5. Click here

    REMOVE REAR DISC


    1. A017FKWE01

      Put matchmarks on the rear disc and the axle hub.

    2. A017DGC

      Release the parking brake and remove the rear disc.

      Tip:

      If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.

  6. Click here

    REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A017DO5

      Remove the 2 No. 1 parking brake shoe return tension springs.

  7. Click here

    SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A017DZX

      Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.

  8. Click here

    REMOVE PARKING BRAKE SHOE STRUT


    1. A017D5L

      Remove the parking brake shoe strut and the parking brake shoe strut compression spring.

  9. Click here

    SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A017BJJ

      Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.

  10. Click here

    REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A017FWP

      Remove the parking brake shoe adjusting screw set.

  11. Click here

    REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A017D1H

      Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.

  12. Click here

    REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A017C8Y

      Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.

  13. Click here

    REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER


    1. A017B8B

      Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.

      Note:

      Be careful not to damage the No. 3 parking brake cable assembly.

  14. Click here

    REMOVE PARKING BRAKE SHOE LEVER


    1. A017CHL

      Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.

  15. Click here

    REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT


    1. A017CCA

      Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.

  16. Click here

    REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)


    1. A017BVU

      Remove the No. 1 parking brake shoe hold down spring pin.

  17. Click here

    REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)


    1. A017DLJ

      Remove the No. 2 parking brake shoe hold down spring pin.

  18. Click here

    REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD)

    Note:

    Perform this procedure only when the No. 2 parking brake shoe hold down spring pin is replaced.

    Tip:

    Click here.

  19. Click here

    REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD)

    Note:

    Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    Tip:

    Click here.

  20. Click here

    REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)


    1. A017EOW

      Remove the No. 2 parking brake shoe hold down spring pin.

  21. Click here

    REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)


    1. A017DIL

      Remove the No. 1 parking brake shoe hold down spring pin.