PARKING BRAKE ASSEMBLY DISASSEMBLY

Tech Tips


  • Use the same procedures for the RH side and the LH side.

  • The procedures listed below are for the LH side.


  1. REMOVE REAR WHEEL

  2. REMOVE REAR AXLE SHAFT NUT (for 4WD)

    Note

    Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    Tech Tips

    Click here.

  3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)


    1. A017FLR

      Remove the 2 bolts and separate the rear disc brake caliper assembly.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)


    1. A017DLS

      Remove the 2 bolts and separate the rear disc brake caliper assembly.

      Note

      Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.

  5. REMOVE REAR DISC


    1. A017FKWE01

      Put matchmarks on the rear disc and the axle hub.

    2. A017DGC

      Release the parking brake and remove the rear disc.

      Tech Tips

      If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.

  6. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A017DO5

      Remove the 2 No. 1 parking brake shoe return tension springs.

  7. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A017DZX

      Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.

  8. REMOVE PARKING BRAKE SHOE STRUT


    1. A017D5L

      Remove the parking brake shoe strut and the parking brake shoe strut compression spring.

  9. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A017BJJ

      Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.

  10. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A017FWP

      Remove the parking brake shoe adjusting screw set.

  11. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A017D1H

      Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.

  12. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A017C8Y

      Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.

  13. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER


    1. A017B8B

      Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.

      Note

      Be careful not to damage the No. 3 parking brake cable assembly.

  14. REMOVE PARKING BRAKE SHOE LEVER


    1. A017CHL

      Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.

  15. REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT


    1. A017CCA

      Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.

  16. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)


    1. A017BVU

      Remove the No. 1 parking brake shoe hold down spring pin.

  17. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)


    1. A017DLJ

      Remove the No. 2 parking brake shoe hold down spring pin.

  18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD)

    Note

    Perform this procedure only when the No. 2 parking brake shoe hold down spring pin is replaced.

    Tech Tips

    Click here.

  19. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD)

    Note

    Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    Tech Tips

    Click here.

  20. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD)


    1. A017EOW

      Remove the No. 2 parking brake shoe hold down spring pin.

  21. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD)


    1. A017DIL

      Remove the No. 1 parking brake shoe hold down spring pin.