Click here

PARKING BRAKE CABLE INSTALLATION

Click here
Click here
Note:

Before installation, apply high temperature grease to the parts indicated by arrows (Click here).

Click here
  1. Click here

    INSTALL CABLE SUPPORT BRACKET


    1. A017BJ8

      Install the cable support bracket to the No. 3 parking brake cable assembly.

  2. Click here

    INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A017D24E01

      Install the No. 3 parking brake cable assembly with the 2 bolts and 4 nuts.

      Bolt (A)
      8.5 N*m 87 kgf*cm 75 in.*lbf
      Bolt (B)
      6.0 N*m 61 kgf*cm 53 in.*lbf
      Nut
      6.0 N*m 61 kgf*cm 53 in.*lbf
    2. A017FBA

      Install the No. 3 parking brake cable assembly to the backing plate with the 2 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf
  3. Click here

    INSTALL NO. 1 PARKING BRAKE CABLE SUPPORT BRACKET


    1. A017D3R

      Install the No. 1 parking brake cable support bracket to the No. 2 parking brake cable assembly.

  4. Click here

    INSTALL PARKING BRAKE CABLE SUPPORT BRACKET


    1. A017DPT

      Install the parking brake cable support bracket to the No. 2 parking brake cable assembly.

  5. Click here

    INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY


    1. A017CBVE01

      Install the No. 2 parking brake cable assembly with the 2 bolts and 5 nuts.

      Bolt (A)
      8.5 N*m 87 kgf*cm 75 in.*lbf
      Bolt (B)
      6.0 N*m 61 kgf*cm 53 in.*lbf
      Nut
      6.0 N*m 61 kgf*cm 53 in.*lbf
    2. A017B78

      Install the No. 2 parking brake cable assembly to the backing plate with the 2 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf
  6. Click here

    APPLY HIGH TEMPERATURE GREASE


    1. Apply high temperature grease to the backing plate which makes contact with the shoe.

  7. Click here

    INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER


    1. A017BK0

      Using needle-nose pliers, connect the No. 3 parking brake cable assembly to the parking brake shoe lever as shown in the illustration.

  8. Click here

    INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A017C8Y

      Install the No. 2 parking brake shoe return tension spring to the No. 2 parking brake shoe assembly.

  9. Click here

    INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A017D1H

      Connect the No. 2 parking brake shoe return tension spring to install the No. 1 parking brake shoe assembly.

  10. Click here

    INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A017B1Y

      Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.

    2. A017FWP

      Install the parking brake shoe adjusting screw set.

  11. Click here

    INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY


    1. A017BJJ

      Install the No. 2 parking brake shoe assembly to the backing plate with the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring, and No. 2 parking brake shoe hold down spring cup.

  12. Click here

    INSTALL PARKING BRAKE SHOE STRUT


    1. A017D5L

      Install the parking brake shoe strut and the parking brake shoe strut compression spring.

  13. Click here

    INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A017DZX

      Install the No. 1 parking brake shoe assembly to the backing plate with the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring, and No. 2 parking brake shoe hold down spring cup.

  14. Click here

    INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A017DO5

      Install the 2 No. 1 parking brake shoe return tension springs.

      Tip:

      First install the front side spring and then the rear side spring.

  15. Click here

    CHECK PARKING BRAKE INSTALLATION


    1. A017BD0E01

      Check that each part is installed properly.

      Note:

      There should be no oil or grease on the friction surface of the shoe lining and disc.

  16. Click here

    INSTALL REAR DISC


    1. A017FKWE01

      Align matchmarks and install the rear disc.

      Note:

      When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.

  17. Click here

    INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)


    1. A017FLR

      Install the rear disc brake caliper assembly with the 2 bolts.

      78 N*m 795 kgf*cm 57 ft.*lbf
  18. Click here

    INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)


    1. A017DLS

      Install the rear disc brake caliper assembly with the 2 bolts.

      78 N*m 795 kgf*cm 57 ft.*lbf
  19. Click here

    INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY


    1. Pass the No. 1 parking brake cable assembly through the parking brake pedal.

    2. A017DJV

      Install the clip to the No. 1 parking brake cable assembly.

    3. A017DP3

      Temporarily install the adjusting nut.

    4. A017CNN

      Bend the parking brake pedal claw.

  20. Click here

    INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY

    Tip:

    Refer to the instructions for INSTALLATION of the parking brake pedal (Click here).

  21. Click here

    ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)


    1. Remove the driver side knee airbag assembly (Click here).

    2. Completely release the parking brake pedal.

    3. A017DLHE01

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheel.

    5. Temporarily install the hub nuts.

    6. Remove the shoe adjusting hole plug.

    7. A017BNUE01

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Return 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 10 notches at 300 N (31 kgf, 67 lbf)

    12. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      7.0 N*m 71 kgf*cm 62 in.*lbf

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts.

    16. Install the rear wheel.

      103 N*m 1050 kgf*cm 76 ft.*lbf

    17. Install the driver side knee airbag assembly (Click here).

  22. Click here

    ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)


    1. Remove the driver side knee airbag assembly (Click here).

    2. Completely release the parking brake pedal.

    3. A017C4KE01

      Loosen the lock nut and adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheel.

    5. Temporarily install the hub nuts.

    6. Remove the shoe adjusting hole plug.

    7. A017BNUE01

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Return 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 10 notches at 300 N (31 kgf, 67 lbf)

    12. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      7.0 N*m 71 kgf*cm 62 in.*lbf

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts.

    16. Install the rear wheel.

      103 N*m 1050 kgf*cm 76 ft.*lbf

    17. Install the driver side knee airbag assembly (Click here).

  23. Click here

    INSPECT BRAKE WARNING LIGHT


    1. When operating the parking brake pedal, check that the brake warning light illuminates.

      Standard
      The brake warning light always illuminates at the first click.
  24. Click here

    INSTALL REAR WHEEL

    103 N*m 1050 kgf*cm 76 ft.*lbf