PARKING BRAKE PEDAL INSTALLATION


  1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)


    1. A017DXR

      Install the parking brake control pedal assembly with the 3 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    2. A017BUI

      Connect the parking brake switch connector.

    3. A017CHC

      Insert the No. 1 parking brake cable assembly toward the outside of the cabin.

    4. A017FOJ

      Install the No. 1 parking brake cable assembly with the 2 bolts and 2 nuts.

      Torque:
      Bolt
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Nut
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    5. Install the clamp.

    6. A017DLHE02

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  2. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)


    1. A017F7W

      Install the parking brake control pedal assembly with the 3 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    2. A017F04

      Connect the parking brake switch connector.

    3. A017CHC

      Insert the No. 1 parking brake cable assembly toward the outside of the cabin.

    4. A017FE5

      Install the No. 1 parking brake cable assembly to the body with the 2 bolts and 3 nuts.

      Torque:
      Bolt
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      Nut
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    5. Install the clamp.

    6. A017C4KE02

      Temporarily install the lock nut.

      Tech Tips

      After adjusting parking brake pedal travel, tighten the lock nut.

  3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)


    1. Connect the connectors to the back of the instrument panel junction block assembly.

    2. A017BKC

      Engage the wire harness clamp onto the instrument panel junction block assembly.

    3. A017D3T

      Install the instrument panel junction block assembly with the 3 nuts.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

    4. Connect the connectors to the instrument panel junction block assembly.

    5. Engage the wire harness clamp onto the instrument panel junction block assembly.

  4. INSTALL PARKING BRAKE EQUALIZER


    1. A017DIV

      Install the parking brake equalizer to the No. 1 parking brake cable assembly as shown in the illustration.

    2. A017D9P

      Slide the rubber boot back as shown in the illustration.

  5. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. A017E8J

      Connect the No. 3 parking brake cable assembly to the parking brake equalizer.

  6. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tech Tips

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  7. INSTALL REAR ENGINE SERVICE COVER ASSEMBLY


    1. A017EL2

      Install the rear engine service cover assembly with the 2 bolts.

  8. INSTALL CENTER FRONT FLOOR COVER


    1. A017FB6

      Engage the 4 clips to install the center front floor cover.

    2. A017BX6

      Install the 4 bolts, 2 screws, and the nut.

  9. INSTALL FRONT FLOOR FOOTREST (for LHD)


    1. A017FZP

      Engage the 2 clips to install the front floor footrest.

  10. INSTALL REAR NO. 1 AIR DUCT


    1. A017EOG

      Install the rear No. 1 air duct.

    2. Engage the wire harness clamp.

  11. INSTALL REAR NO. 2 AIR DUCT


    1. A017G0F

      Install the rear No. 2 air duct with the clip.

    2. Install the floor carpet.

  12. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)


    1. A017FLQ

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.

  13. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)


    1. A017BG4

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <F> and clip.

  14. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017G3R

      Engage the 6 claws.

    2. A017E57

      Install the console box assembly with the 4 bolts and 2 screws.

  15. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017E8O

      Engage the 6 claws.

    2. Connect the connector.

    3. A017C3F

      Install the console box assembly with the 4 bolts and 2 screws.

  16. INSTALL LOWER REAR CONSOLE BOX


    1. Install the lower rear console box.

  17. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    1. A017F5N

      Install the No. 2 console box duct as shown in the illustration.

  18. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Connect the connector.

    2. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.

  19. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)


    1. A017EYQE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  20. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017D5UE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  21. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)


    1. A017EX3

      Engage the 2 claws to install the No. 1 air duct sub-assembly.

  22. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. A017CGP

      Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.

  23. INSTALL REAR DOOR SCUFF PLATE LH


    1. A017D4T

      Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

  24. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  25. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  26. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)

    Tech Tips

    Use the same procedure for the LHD model Click here.

  27. INSTALL FRONT DOOR SCUFF PLATE LH (for RHD)

    Tech Tips

    Use the same procedure for the LHD model Click here.

  28. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for LHD)


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017F8J

      Install the DLC3 to the driver side knee airbag assembly with the 2 claws.

    4. A017EBJ

      Connect the connector to the driver side knee airbag assembly.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    5. A017EHS

      Support the driver side knee airbag assembly with one hand as shown in the illustration.

    6. A017CTB

      Temporarily install the driver side knee airbag assembly with the 2 hooks.

    7. A017FEG

      Install the driver side knee airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  29. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD Manual Air Conditioning System)


    1. A017BY3

      Connect the hood lock control cable assembly.

    2. Connect each connector.

    3. Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  30. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD Automatic Air Conditioning System)


    1. A017CWD

      Connect the hood lock control cable assembly.

    2. Connect each connector and the aspirator duct.

    3. A017EU2

      Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)


    1. A017G63

      Engage the claw and clip, install the cowl side trim sub-assembly LH.

    2. Install the clip.

  32. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)


    1. A017B6P

      Engage the guide and the 8 claws, and install the front door scuff plate LH.

  33. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for RHD)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  34. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for RHD Manual Air Conditioning System)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  35. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for RHD Automatic Air Conditioning System)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  36. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  37. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    This is symmetrical to the LHD model Click here.

  38. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Temporarily install the front seat assembly with the 4 bolts.

    4. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    5. A017D8FE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    6. Lift up the seat track adjusting handle and move the seat to the foremost position.

    7. A017G32E01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  39. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for Manual Seat)


    1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.

      If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.

  40. INSTALL REAR SEAT TRACK COVER LH (for Manual Seat)


    1. A017CWY

      Engage the 4 claws and install the 2 rear seat track covers.

  41. INSTALL FRONT INNER SEAT TRACK COVER LH (for Manual Seat)


    1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    2. A017DLZ

      Engage the 2 claws and install the front inner seat track cover.

  42. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Manual Seat)


    1. A017FOO

      Engage the 2 claws and install the front outer seat track cover.

  43. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Manual Seat)

  44. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Connect the cable to the negative (-) battery terminal.

      Note

      When reconnected the cable, some systems need to be initialized Click here.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the power seat switch knob and move the seat to the rearmost position.

    6. A017FKLE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    7. Operate the power seat switch knob and move the seat to the foremost position.

    8. A017B0KE01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  45. INSTALL REAR INNER SEAT TRACK COVER LH (for Power Seat)


    1. A017DBE

      Engage the 2 claws and install the rear inner seat track cover.

  46. INSTALL REAR OUTER SEAT TRACK COVER LH (for Power Seat)


    1. A017DLU

      Engage the 2 claws and install the rear outer seat track cover.

  47. INSTALL FRONT INNER SEAT TRACK COVER LH (for Power Seat)


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A017F34

      Engage the 2 claws and install the front inner seat track cover.

  48. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Power Seat)


    1. A017ET7

      Engage the 2 claws and install the front outer seat track cover.

  49. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Power Seat)

  50. INSPECT FRONT SEAT ASSEMBLY LH (for Power Seat)


    1. Inspect the power seat operation.

    2. w/ Seat Heater System:

      Check the seat heater operation.


      1. Turn the ignition switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

  51. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)


    1. Remove the driver side knee airbag assembly Click here.

    2. Completely release the parking brake pedal.

    3. A017DLHE01

      Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheel.

    5. Temporarily install the hub nuts.

    6. Remove the shoe adjusting hole plug.

    7. A017BNUE01

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Return 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 10 notches at 300 N (31 kgf, 67 lbf)

    12. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts.

    16. Install the rear wheel.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    17. Install the driver side knee airbag assembly Click here.

  52. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)


    1. Remove the driver side knee airbag assembly Click here.

    2. Completely release the parking brake pedal.

    3. A017C4KE01

      Loosen the lock nut and adjusting nut to completely release the parking brake cable.

    4. Remove the rear wheel.

    5. Temporarily install the hub nuts.

    6. Remove the shoe adjusting hole plug.

    7. A017BNUE01

      Turn the shoe adjuster and expand the shoe until the disc locks.

    8. Turn and contract the shoe adjuster until the disc can rotate smoothly.

      Standard
      Return 8 notches.

    9. Check that there is no brake drag against the shoe.

    10. Install the shoe adjusting hole plug.

    11. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

      Parking brake pedal travel
      8 to 10 notches at 300 N (31 kgf, 67 lbf)

    12. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    13. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

    14. Check that there is no brake drag against the shoe.

    15. Remove the hub nuts.

    16. Install the rear wheel.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

    17. Install the driver side knee airbag assembly Click here.

  53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  54. INSPECT BRAKE WARNING LIGHT


    1. When operating the parking brake pedal, check that the brake warning light illuminates.

      Standard
      The brake warning light always illuminates at the first click.

  55. INSPECT SRS WARNING LIGHT

    Tech Tips

    Click here.