FRONT BRAKE REASSEMBLY


  1. INSTALL FRONT DISC


    1. A017EY2E01

      Align the matchmarks and install the front disc.

      Note

      When replacing the disc with a new one, select the installation position where the front disc has minimal runout.

  2. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG


    1. Temporarily tighten the front disc brake bleeder plug to the disc brake cylinder sub-assembly.

  3. INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP


    1. Install the bleeder plug cap to the front disc brake bleeder plug.

  4. INSTALL PISTON SEAL


    1. Apply lithium soap base glycol grease to a new piston seal.

    2. Install the piston seal to the disc brake cylinder assembly.

      Note

      Securely install the piston seal into the groove of the disc brake cylinder.

  5. INSTALL FRONT DISC BRAKE PISTON


    1. A017BR3E01

      Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.

    2. Install the cylinder boot to the front disc brake piston.

    3. Apply a light layer of lithium soap base glycol grease to the contact surfaces of the front disc brake piston, and install the front disc brake piston to the disc brake cylinder assembly.

      Note

      Do not install the front disc brake piston forcibly in the disc brake cylinder assembly.

  6. INSTALL CYLINDER BOOT


    1. A017DVZ

      Install the cylinder boot to the front disc brake cylinder assembly as shown in the illustration.

      Note


      • Securely install the cylinder boot into the groove of the cylinder and piston.

      • Do not damage the cylinder boot.

  7. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING


    1. A017BXS

      Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

      Torque:
      104 N*m  { 1060 kgf*cm, 76 ft.*lbf }

  8. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT


    1. A017C98E01

      Apply lithium soap base glycol grease to the seal surface of 2 new front disc brake bushing dust boots.

    2. Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.

  9. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING


    1. A017FH7E04

      Apply lithium soap base glycol grease to a new front disc brake cylinder slide bushing.

    2. Install the front disc brake cylinder slide bushing to the No. 2 front disc brake cylinder slide pin.

  10. INSTALL NO. 1 FRONT DISC BRAKE CYLINDER SLIDE PIN


    1. A017G6XE01

      Apply lithium soap base glycol grease to the sliding part and the seal surface of the No. 1 front disc brake cylinder slide pin.

    2. Install the No. 1 front disc brake cylinder slide pin.

  11. INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN


    1. A017BEME01

      Apply lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 front disc brake cylinder slide pin.

    2. Install the No. 2 front disc brake cylinder slide pin to the bottom side of the front disc brake cylinder mounting.

  12. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE


    1. A017CMR

      Install the 4 front disc brake pad support plates to the front disc brake cylinder mounting as shown in the illustration.

      Note

      Be sure to install each front disc brake pad support plate to the correct position and direction.

  13. INSTALL FRONT ANTI-SQUEAL SHIM


    1. A017FCHE01

      Apply disc brake grease to the inside of the 2 front anti-squeal shims as shown in the illustration.

      Note


      • When replacing worn pads, the front anti-squeal shims must be replaced together with the pads.

      • Install the shims in the correct positions and directions.

      • Apply disc brake grease to the area that contacts the front anti-squeal shim.

      • Disc brake grease can come out slightly from the area where the front anti-squeal shim is installed.

      • Make sure that disc brake grease is not applied onto the lining surface.

    2. A017GA8E01

      Install the 2 front anti-squeal shims and the 2 pad wear indicators to the pads.

      Note

      Install the pad wear indicators in the correct positions and directions.

  14. INSTALL FRONT DISC BRAKE PAD


    1. A017FWZ

      Install the 2 brake pads with the front anti-squeal shims to the front disc brake cylinder mounting.

    2. A017C53

      Install the 2 anti-squeal springs to the front disc brake pads.

      Note


      • When replacing the front brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

      • Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.