Click here

VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:C1425

Click here
Click here
DTC Code DTC Name
C1425 Open in Stop Light Switch Circuit
Click here

DESCRIPTION

The skid control ECU (housed in the actuator assembly) inputs stop light switch signals and the condition of brake operation.

The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code DTC Detection Condition Trouble Area
C1425 When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit continues for 3 seconds or more.

  • STOP fuse

  • Stop light switch

  • Stop light switch circuit

  • Stop light control relay

  • Stop light control relay circuit

  • Brake actuator assembly (Skid control ECU)
A017BF0E02
Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

When replacing the brake actuator assembly, perform zero point calibration (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK STOP LIGHT OPERATION


    1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

      OK
      Condition Illumination Condition
      Brake pedal depressed ON
      Brake pedal released OFF

  2. Click here

    READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Select the Data List mode on the intelligent tester (Click here).

      Table 1. ABS / VSC / TRC:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Lamp SW Stop light switch / ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -

    4. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

      OK
      The intelligent tester displays ON or OFF according to brake pedal operation.

  3. Click here

    RECONFIRM DTC


    1. Turn the ignition switch off.

    2. Clear the DTCs (Click here).

    3. Start the engine.

    4. Depress the brake pedal several times to test the stop light circuit.

    5. Check if the same DTC is recorded (Click here).

      Result
      Result Proceed to
      DTC (C1425) is not output A
      DTC (C1425) is output B
      Tip:

      If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).


  4. Click here

    INSPECT STOP FUSE


    1. A017FBOE02

      Remove the STOP fuse from the main body ECU (instrument panel junction block).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      STOP (10 A) fuse Always Below 1 Ω

  5. Click here

    INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)


    1. A017GBJE13

      Install the STOP fuse.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the stop light switch connector.

    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      A20-2 - Body ground Always 11 to 14 V

  6. Click here

    INSPECT STOP LIGHT SWITCH


    1. A017BK7E03

      Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      1 - 2 Switch pin free Below 1 Ω
      1 - 2 Switch pin pushed in 10 kΩ or higher

  7. Click here

    INSPECT STOP LIGHT CONTROL RELAY


    1. A017B3RE06

      Remove the stop light control relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      3 - 4 Voltage is not applied between terminals 1 and 2 Below 1 Ω

  8. Click here

    CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ENGINE ROOM RELAY BLOCK)


    1. A017B4KE02

      Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A20-1 - Stop light control relay terminal 4 Always Below 1 Ω
      A20-1 - Body ground Always 10 kΩ or higher

  9. Click here

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)


    1. A017E2EE01

      Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Disconnect the skid control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A24-2 (STP) - Stop light control relay terminal 3 Always Below 1 Ω
      A24-2 (STP) - Body ground Always 10 kΩ or higher

  10. Click here

    RECONFIRM DTC


    1. Clear the DTCs (Click here).

    2. Start the engine.

    3. Depress the brake pedal several times to test the stop light circuit.

    4. Check if the same DTC is recorded (Click here).

      Tip:

      Reinstall the relay, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

      Result
      Result Proceed to
      DTC (C1425) is not output A
      DTC (C1425) is output B
      Tip:

      If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).


  11. Click here

    CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)


    1. A017E2EE01

      Turn the ignition switch off.

    2. Remove the stop light control relay.

    3. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    4. Disconnect the skid control ECU connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A24-2 (STP) - Stop light control relay terminal 3 Always Below 1 Ω
      A24-2 (STP) - Body ground Always 10 kΩ or higher
      Tip:

      If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).


  12. Click here

    CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION)Click here

  13. Click here

    INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)Click here

  14. Click here

    REPLACE BRAKE ACTUATOR ASSEMBLYClick here

  15. Click here

    REPLACE STOP FUSE

  16. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

  17. Click here

    REPLACE STOP LIGHT SWITCHClick here

  18. Click here

    REPLACE STOP LIGHT CONTROL RELAY

  19. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR