ROOF HEADLINING (for Full-trim) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 1 SEAT ASSEMBLY


    1. A01BDBC

      First row:


      1. Remove the 3 bolts, nut and rear No.1 seat assembly.

    2. A01BI53

      Second row:


      1. Remove the 2 bolts, 2 nuts and rear No.1 seat assembly.

  4. REMOVE REAR NO. 2 SEAT ASSEMBLY


    1. A01BFKN

      Remove the 4 bolts, 2 nuts and rear No.2 seat assembly.

      Tech Tips


      • Use the same procedure for the second row.

      • Use the same procedure for the third row.

  5. REMOVE REAR NO. 3 SEAT ASSEMBLY


    1. for Bench Type Seatback:

      Remove the rear No. 3 seat assembly Click here.

    2. for Separate Type Seatback:

      Remove the rear No. 3 seat assembly Click here.

  6. REMOVE REAR NO. 4 SEAT ASSEMBLY


    1. A01BDT2

      Remove the 3 bolts and 2 nuts.

    2. Pull the lever in the direction indicated by the arrow in the illustration, release the 2 locks, and remove the rear No.4 seat assembly.

  7. REMOVE REAR SEAT BELT ASSEMBLY OUTER


    1. A01BF9V

      Remove the bolt and disconnect the floor side of the rear seat belt assembly outer.

    2. A01BEOJ

      Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BFZ5

      Loosen the bolt and disconnect the shoulder side of the rear seat belt assembly outer.

    4. A01BDAM

      Loosen the bolt and remove the rear seat belt assembly outer.

    5. for Rear No. 1 Seat Bench Seat Type:


      1. A01BHAU

        w/ Cover:

        Detach the 3 claws and 3 guides, and then remove the side trim cover.

      2. Loosen the bolt and disconnect the floor side of the rear seat belt assembly outer.

        A01BEOIE01
        Text in Illustration
        *A w/o Cover *B w/ Cover
      3. A01BH1T

        Using a screwdriver, detach the 2 claws and open the shoulder side cover of the rear seat belt assembly outer.

        Tech Tips

        Tape the screwdriver tip before use.

      4. A01BGPP

        Loosen the bolt and disconnect the shoulder side of the rear seat belt assembly outer.

      5. A01BEHE

        Loosen the bolt.

      6. Detach the 2 claws and remove the retractor cover of the rear seat belt assembly outer.

      7. A01BCS5

        Remove the 2 bolts and rear seat belt assembly outer.

    6. w/ Cover:


      1. Remove the bolt from the floor side of the rear seat belt assembly outer.

      2. Remove the side trim cover from the rear seat belt assembly outer.

  8. REMOVE REAR NO. 2 SEAT BELT ASSEMBLY OUTER


    1. A01BFZF

      Remove the bolt and disconnect the floor side of the rear No. 2 seat belt assembly outer.

    2. A01BGW6

      Using a screwdriver, detach the 2 claws and open the shoulder side cover of the rear No. 2 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BACW

      Remove the bolt and disconnect the shoulder side of the rear No. 2 seat belt assembly outer.

    4. A01BCQQ

      Remove the bolt and rear No. 2 seat belt assembly outer.

  9. REMOVE REAR NO. 3 SEAT BELT ASSEMBLY OUTER


    1. A01BHKL

      Remove the bolt and disconnect the floor side of the rear No. 3 seat belt assembly outer.

    2. A01BEOL

      Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear No. 3 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BCWA

      Loosen the bolt and disconnect the shoulder side of the rear No. 3 seat belt assembly outer.

    4. A01BE7O

      Using a screwdriver, detach the 4 claws and remove the retractor cover of the rear No. 3 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    5. A01BCED

      Remove the bolt and rear No. 3 seat belt assembly outer.

  10. REMOVE REAR NO. 4 SEAT BELT ASSEMBLY OUTER


    1. A01BBPR

      Remove the bolt and disconnect the floor side of the rear No. 4 seat belt assembly outer.

    2. A01BCNU

      Using a screwdriver, detach the 2 claws and open the shoulder side cover of the rear No. 4 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BGFF

      Remove the bolt and disconnect the shoulder side of the rear No. 4 seat belt assembly outer.

    4. A01BHXU

      Using a screwdriver, detach the 4 claws and remove the retractor cover of the rear No. 4 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    5. A01BAOA

      Remove the bolt and rear No. 4 seat belt assembly outer.

  11. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01BGMI

      Detach the 5 clips and remove the front door scuff plate LH.

  12. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. REMOVE FRONT DOOR OPENING TRIM LH

  14. REMOVE FRONT DOOR OPENING TRIM RH

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH


    1. A01BF0I

      Remove the bolt and disconnect front seat outer belt assembly RH.

    2. A01BAR9E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BGXI

      Remove the bolt and disconnect front seat outer belt assembly RH.

  16. REMOVE CENTER PILLAR GARNISH COVER LOWER LH


    1. A01BHX3E01

      Using a screwdriver, detach the 4 claws and remove the center pillar garnish cover lower LH.

      Tech Tips

      Tape the screwdriver tip before use.

  17. REMOVE SEAT ASSEMBLY LH


    1. Disconnect connector.

    2. A01BAVH

      Remove the nut and 3 bolts.

    3. Remove the seat assembly LH.

  18. REMOVE SEAT BELT ANCHOR COVER


    1. A01BB5PE01

      Remove the 2 clips.

    2. Detach the claw and then remove the seat belt anchor cover.

  19. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01BAV9

      Remove the bolt and disconnect the front seat outer belt assembly LH.

    2. A01BA80E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BF4Z

      Remove the bolt and disconnect the front seat outer belt assembly LH.

  20. REMOVE REAR DOOR SCUFF PLATE RH


    1. A01BAVP

      Detach the 11 clips and remove the rear door scuff plate RH.

  21. REMOVE SLIDE DOOR WEATHERSTRIP NO. 1 RH

  22. REMOVE BACK DOOR SCUFF PLATE


    1. A01BBWNE01

      Detach the 7 clips and 4 claws and remove the back door scuff plate.

  23. REMOVE BACK DOOR WEATHERSTRIP

  24. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH (for Middle Roof)


    1. A01BHB3

      Detach the 21 clips and remove the quarter trim panel assembly rear LH.

  25. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR LH (for High Roof)


    1. A01BFM6

      Detach the 35 clips and remove the quarter trim panel assembly rear LH.

  26. REMOVE QUARTER TRIM PANEL ASSEMBLY REAR RH

    Tech Tips

    Use the same procedures described for the LH side.

  27. REMOVE SIDE NO. 1 TRIM ASSEMBLY LH


    1. A01BFUT

      Detach the 21 clips and remove the side No. 1 trim assembly LH.

  28. REMOVE ENGINE SERVICE HOLE COVER HOOK NO. 2 LH


    1. A01BBRY

      Remove the screw and engine service hole cover hook No. 2 LH.

  29. REMOVE CENTER PILLAR GARNISH LH


    1. A01BE1W

      Detach the 5 clips and 2 claws, and remove the center pillar garnish LH.

  30. REMOVE ASSIST GRIP PLUG


    1. A01BC0Y

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip plugs.

      Tech Tips

      Tape the screwdriver tip before use.

  31. REMOVE ASSIST GRIP ASSEMBLY REAR


    1. A01BD7L

      Remove the 2 screws and assist grip assembly rear.

  32. REMOVE CENTER PILLAR GARNISH LOWER RH


    1. A01BDYB

      Detach the 4 claws and remove the center pillar garnish lower RH.

  33. REMOVE CENTER PILLAR GARNISH RH


    1. A01BC8O

      Detach the 3 clips, claw and remove the center pillar garnish RH.

  34. REMOVE QUARTER PILLAR GARNISH LH (for High Roof)


    1. A01BFP3E02

      Detach the 6 clips and remove the quarter pillar garnish LH.

  35. REMOVE QUARTER PILLAR GARNISH RH (for High Roof)

    Tech Tips

    Use the same procedures described for the LH side.

  36. REMOVE QUARTER PILLAR GARNISH LH (for Middle Roof)


    1. A01BFSR

      Detach the 3 clips and remove the quarter pillar garnish LH.

  37. REMOVE QUARTER PILLAR GARNISH RH (for Middle Roof)

    Tech Tips

    Use the same procedures described for the LH side.

  38. REMOVE ROOF SIDE GARNISH INNER UPPER LH


    1. A01BCRQ

      Using a screwdriver, detach the 6 clips and remove the roof side garnish inner upper LH.

      Tech Tips

      Tape the screwdriver tip before use.

  39. REMOVE ROOF SIDE GARNISH INNER UPPER RH

    Tech Tips

    Use the same procedures described for the LH side.

  40. REMOVE REAR SEAT HOOK (for Space Up Seat)


    1. A01BG06

      Remove the bolt and rear seat hook.

  41. REMOVE ROOM LIGHT ASSEMBLY NO. 2 (Deluxe)


    1. A01BCQRE03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the room light lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BG0A

      Remove the 2 screws and room light assembly No. 2.

    3. Disconnect the connector.

  42. REMOVE ROOM LIGHT ASSEMBLY NO. 2 (Super Wagon)


    1. A01BA8B

      Using a screwdriver, detach the 4 claws and remove the room light base.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. A01BD2XE01

      Pull the room light assembly No. 2 rearward and detach the 2 claws and remove it.

    4. Disconnect the connector.

  43. REMOVE ROOF HEADLINING NO. 2 (for Middle Roof)


    1. A01BEDBE01

      Using a clip remover, remove the 19 clips.

    2. Using a clip remover, detach the clip A and remove the roof headlining No. 2.

  44. REMOVE ROOF HEADLINING NO. 2 (for High Roof)

    A01BDH1E01

    1. Using a clip remover, remove the 25 clips.

    2. Using a clip remover, detach the clip A and remove the roof headlining No. 2.

  45. REMOVE FRONT ASSIST GRIP PLUG NO. 1


    1. A01BGF8

      Using a screwdriver, detach the 4 claws and remove the 2 front assist grip plugs No. 1.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedures described for the other side.

  46. REMOVE ASSIST GRIP ASSEMBLY


    1. A01BDF5

      Remove the 2 screws and assist grip assembly.

      Tech Tips

      Use the same procedures described for the other side.

  47. REMOVE FRONT PILLAR GARNISH LH


    1. A01BHII

      Detach the clip and claw and remove the front pillar garnish LH.

  48. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  49. REMOVE ASSIST GRIP


    1. A01BGK9E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 6 claws and open the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BDOY

      Remove the 2 screws and assist grip.

  50. REMOVE VISOR ASSEMBLY LH


    1. A01BB5I

      Remove the 2 screws and visor assembly LH.

  51. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  52. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedures described for the other side.


    1. A01BDBA

      Remove the screw.

    2. Using a moulding remover, detach the claw and remove the visor holder.

  53. REMOVE ROOM LIGHT ASSEMBLY NO. 1 (Deluxe)


    1. A01BCQRE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the room light lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BG0A

      Remove the 2 screws and room light assembly No. 1.

    3. Disconnect the connector.

  54. REMOVE MAP LIGHT ASSEMBLY (Super Wagon)


    1. A01BAKAE01

      Using a moulding remover, detach the 4 claws and map light assembly.

    2. Disconnect the connector.

  55. REMOVE REAR COOLER CONTROL PANEL


    1. A01BAYSE01

      Release the 4 clips and 4 claws, and disconnect the rear cooler control panel.

    2. Disconnect the connector and remove the rear cooler control panel.

  56. REMOVE ROOF HEADLINING NO. 1 (for Middle Roof)


    1. A01BEWOE03

      Remove the 4 screws.

    2. Using a clip remover, remove the 8 clips.

    3. Using a clip remover, detach the clip A and remove the roof headlining No. 1.

  57. REMOVE ROOF HEADLINING NO. 1 (for High Roof)

    A01BDPHE03

    1. Remove the 4 screws.

    2. Using a clip remover, remove the 14 clips.

    3. Using a clip remover, detach the clip A and remove the roof headlining No. 1.