ROOF HEADLINING (w/ Roof Window Glass) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE NO. 2 ROOM LIGHT ASSEMBLY

    Tech Tips

    Use the same procedure described for the other side.


    1. A01BDNPE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the light cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BG0A

      Remove the 2 screws and No. 2 room light assembly.

    3. Disconnect the connector.

  4. REMOVE BACK DOOR SCUFF PLATE (w/ Rear Air Conditioning System)


    1. A01BBWNE01

      Detach the 7 clips and 4 claws and remove the back door scuff plate.

  5. REMOVE BACK DOOR WEATHERSTRIP (w/ Rear Air Conditioning System)

  6. DISCONNECT REAR NO. 4 SEAT BELT ASSEMBLY OUTER (w/ Rear Air Conditioning System)

    Tech Tips

    Use the same procedure described for the other side.


    1. A01BEOJ

      Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear No. 4 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BFZ5

      Loosen the bolt and disconnect the shoulder side of the rear No. 4 seat belt assembly outer.

  7. REMOVE ROOF HEADLINING MOULDING (w/o Rear Air Conditioning System)


    1. A01BGQA

      Detach the 18 clips and 2 roof headlining mouldings.

      Tech Tips

      If any clip remains on the body side, use a clip remover.

  8. REMOVE REAR ROOF HEADLINING GARNISH (w/o Rear Air Conditioning System)


    1. A01BHKQ

      Detach the 18 clips and remove the rear roof headlining garnish.

  9. REMOVE REAR ROOF HEADLINING GARNISH (w/ Rear Air Conditioning System)


    1. A01BB6W

      Detach the 18 clips and remove the rear roof headlining garnish.

  10. REMOVE ROOF CLIP (w/o Rear Air Conditioning System)


    1. A01BAXJ

      Using a screwdriver, detach the 2 claws and remove the roof clip.

      Tech Tips

      Tape the screwdriver tip before use.

  11. REMOVE NO. 4 ROOF HEADLINING (w/o Rear Air Conditioning System)


    1. A01BGTJ

      Remove the 17 clips and No. 4 roof headlining.

  12. REMOVE NO. 3 ROOF HEADLINING (w/o Rear Air Conditioning System)


    1. A01BCGI

      Remove the 3 clips and No. 3 roof headlining.

  13. REMOVE NO. 2 ROOF HEADLINING (w/o Rear Air Conditioning System)


    1. A01BECU

      Remove the 5 clips and No. 2 roof headlining.

  14. REMOVE NO. 2 ROOF HEADLINING (w/ Rear Air Conditioning System)

    A01BG7BE01

    1. Using a clip remover, remove the 18 clips.

    2. Using a clip remover, detach the 4 clips A and remove the No. 2 roof headlining.

  15. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01BGMI

      Detach the 5 clips and remove the front door scuff plate LH.

  16. REMOVE FRONT DOOR SCUFF PLATE RH


    1. A01BHXN

      Detach the 5 clips and remove the front door scuff plate RH.

  17. REMOVE FRONT DOOR OPENING TRIM RH

  18. REMOVE FRONT DOOR OPENING TRIM LH

  19. REMOVE ASSIST GRIP PLUG


    1. A01BCSQ

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip plugs.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure described for the other side.

  20. REMOVE ASSIST GRIP ASSEMBLY


    1. A01BAU2

      Remove the 2 screws and assist grip assembly.

      Tech Tips

      Use the same procedure described for the other side.

  21. REMOVE FRONT PILLAR GARNISH RH


    1. A01BHWK

      Detach the clip and 2 claws and remove the front pillar garnish RH.

  22. REMOVE FRONT PILLAR GARNISH LH

    Tech Tips

    Use the same procedure described for the RH side.

  23. DISCONNECT REAR NO. 3 SEAT BELT ASSEMBLY OUTER (w/ Rear Air Conditioning System)


    1. A01BEOL

      Using a screwdriver, detach the 4 claws and open the shoulder side cover of the rear No. 3 seat belt assembly outer.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BCWA

      Loosen the bolt and disconnect the shoulder side of the rear No. 3 seat belt assembly outer.

  24. REMOVE ASSIST GRIP (w/o Rear Air Conditioning System)


    1. A01BAR2E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 6 claws and open the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BDOY

      Remove the 2 screws and assist grip.

  25. REMOVE CENTER PILLAR GARNISH COVER LOWER LH (w/ Rear Air Conditioning System)


    1. A01BHX3E01

      Using a screwdriver, detach the 4 claws and remove the center pillar garnish cover lower LH.

      Tech Tips

      Tape the screwdriver tip before use.

  26. REMOVE SEAT ASSEMBLY LH (w/ Rear Air Conditioning System)


    1. Disconnect connector.

    2. A01BAVH

      Remove the nut and 3 bolts.

    3. Remove the seat assembly LH.

  27. REMOVE SEAT BELT ANCHOR COVER (w/ Rear Air Conditioning System)


    1. A01BB5PE01

      Remove the 2 clips.

    2. Detach the claw and then remove the seat belt anchor cover.

  28. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Rear Air Conditioning System)


    1. A01BAV9

      Remove the bolt and disconnect the front seat outer belt assembly LH.

    2. A01BA80E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BF4Z

      Remove the bolt and disconnect the front seat outer belt assembly LH.

  29. REMOVE CENTER PILLAR GARNISH LOWER LH (w/ Rear Air Conditioning System)


    1. A01BBOJE01

      Using a screwdriver, detach the 4 clips and remove the center pillar garnish lower LH.

  30. REMOVE ENGINE SERVICE HOLE COVER HOOK NO. 2 LH (w/ Rear Air Conditioning System)


    1. A01BGNS

      Remove the screw and the engine service hole cover hook No. 2 LH.

  31. REMOVE CENTER PILLAR GARNISH LH (w/ Rear Air Conditioning System)


    1. A01BFR4E01

      Using a screwdriver, detach the 3 clips and claw, and remove the center pillar garnish LH.

  32. REMOVE REAR DOOR SCUFF PLATE RH (w/ Rear Air Conditioning System)


    1. A01BAVP

      Detach the 11 clips and remove the rear door scuff plate RH.

  33. REMOVE SLIDE DOOR WEATHERSTRIP NO. 1 RH (w/ Rear Air Conditioning System)

  34. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (w/ Rear Air Conditioning System)


    1. A01BF0I

      Remove the bolt and disconnect front seat outer belt assembly RH.

    2. A01BAR9E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

    3. A01BGXI

      Remove the bolt and disconnect front seat outer belt assembly RH.

  35. REMOVE CENTER PILLAR GARNISH LOWER RH (w/ Rear Air Conditioning System)


    1. A01BGYFE01

      Remove the clip.

    2. Using a screwdriver, detach the 4 clips and remove the center pillar garnish lower RH.

      Tech Tips

      Tape the screwdriver tip before use.

  36. REMOVE CENTER PILLAR GARNISH RH (w/ Rear Air Conditioning System)


    1. A01BC8O

      Detach the 3 clips, claw and remove the center pillar garnish RH.

  37. REMOVE BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Rear Air Conditioning System)

    Tech Tips

    Use the same procedure for all back window glass hammers.


    1. Remove the 2 bolts.

    2. Detach the claw and 2 guides.

    3. Disconnect the connector and remove the back window glass hammer.

      A01BHHOE01
      Text in Illustration
      *A for Super Long Wheelbase *B for Long Wheelbase

  38. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. A01BDNPE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the light cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01BG0A

      Remove the 2 screws and No. 1 room light assembly.

    3. Disconnect the connector.

  39. REMOVE VISOR ASSEMBLY LH


    1. A01BB5I

      Remove the 2 screws and visor assembly LH.

  40. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  41. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure described for the other side.


    1. A01BDBA

      Remove the screw.

    2. Using a moulding remover, detach the claw and remove the visor holder.

  42. REMOVE REAR COOLER CONTROL PANEL (w/ Rear Air Conditioning System)


    1. A01BAYSE01

      Release the 4 clips and 4 claws, and disconnect the rear cooler control panel.

    2. Disconnect the connector and remove the rear cooler control panel.

  43. REMOVE NO. 1 ROOF HEADLINING (w/o Rear Air Conditioning System)


    1. Using a clip remover, remove the 6 clips.

    2. A01BBMXE01

      Using a clip remover, detach the clip A and remove the No. 1 roof headlining.

  44. REMOVE NO. 1 ROOF HEADLINING (w/ Rear Air Conditioning System)

    A01BH9FE01

    1. Remove the 4 screws.

    2. Using a clip remover, remove the 10 clips.

    3. Using a clip remover, detach the clip A and remove the roof headlining No. 1.