SLIDE DOOR CLOSER SYSTEM Slide Door Closer Motor RH Circuit

DESCRIPTION



WIRING DIAGRAM


  1. w/ Power Slide Door

    A01BBUVE02

  2. w/o Power Slide Door

    A01BI5HE02

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK VEHICLE TYPE


    1. Check vehicle type.

      Result
      Result Proceed to
      w/o Power Slide Door A
      w/ Power Slide Door B

    B

    INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH Click here

    A

  2. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH


    1. Check the motor.


      1. Remove the power slide door lock assembly RH Click here.

      2. Inspect the power slide door lock assembly RH Click here.

    2. Check the switches.


      1. Remove the power slide door lock assembly RH Click here.

      2. Inspect the power slide door lock assembly RH Click here.

      Result
      Result Proceed to
      OK A
      NG (malfunctioning in motor) B
      NG (malfunctioning in switches) C

    B

    REPLACE POWER SLIDE DOOR LOCK ASSEMBLY RH Click here

    C

    REPLACE DOOR LOCK SWITCH RH

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  3. INSPECT POWER SLIDE DOOR LOCK ASSEMBLY RH


    1. Check the motor.


      1. Remove the power slide door lock assembly RH Click here.

      2. Inspect the power slide door lock assembly RH Click here.

    2. Check the switches.


      1. Remove the power slide door lock assembly RH Click here.

      2. Inspect the power slide door lock assembly RH Click here.

      Result
      Result Proceed to
      OK A
      NG (malfunctioning in motor) B
      NG (malfunctioning in switches) C

    B

    REPLACE POWER SLIDE DOOR LOCK ASSEMBLY RH Click here

    C

    REPLACE DOOR LOCK SWITCH RH

    A

  4. INSPECT REAR DOOR WIRE RH


    1. A01BDMZE01
      Text in Illustration
      *a

      Rear Door Wire RH

      (Door Control Relay Assembly Side)
      *b

      Rear Door Wire RH

      (Power Slide Door Lock Assembly RH Side)

      Disconnect the ci1 and fc1 rear door wire RH connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-4 - B-18 Always Below 1 Ω
      A-5 - B-12 Always Below 1 Ω
      A-7 - B-8 Always Below 1 Ω
      A-10 - B-16 Always Below 1 Ω
      A-11 - B-15 Always Below 1 Ω
      A-16 - B-14 Always Below 1 Ω
      A-17 - B-9 Always Below 1 Ω

    NG

    REPLACE REAR DOOR WIRE RH Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RELAY ASSEMBLY - POWER SLIDE DOOR LOCK ASSEMBLY RH)


    1. Disconnect the I3 and I4 door control relay assembly connectors.

    2. Disconnect the f1 power slide door lock assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I4-1 (DC-) - f1-1 (ACT-) Always Below 1 Ω
      I4-5 (DC+) - f1-2 (ACT+) Always Below 1 Ω
      I3-4 (HAF) - f1-3 (HAF) Always Below 1 Ω
      I3-5 (FUL) - f1-4 (FUL) Always Below 1 Ω
      I3-18 (POL) - f1-9 (POL) Always Below 1 Ω
      I3-19 (LMT) - f1-10 (HND) Always Below 1 Ω
      I3-13 (OSG) - f1-8 (E1) Always Below 1 Ω
      I4-1 (DC-) or f1-1 (ACT-) - Body ground Always 10 kΩ or higher
      I4-5 (DC+) or f1-2 (ACT+) - Body ground Always 10 kΩ or higher
      I3-4 (HAF) or f1-3 (HAF) - Body ground Always 10 kΩ or higher
      I3-5 (FUL) or f1-4 (FUL) - Body ground Always 10 kΩ or higher
      I3-18 (POL) or f1-9 (POL) - Body ground Always 10 kΩ or higher
      I3-19 (LMT) or f1-10 (HND) - Body ground Always 10 kΩ or higher
      I3-13 (OSG) or f1-8 (E1) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here