ENGINE IMMOBILISER SYSTEM (w/o Smart Entry and Start System) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Immobiliser or Engine and ECT / Data List.

    5. Read the Data List according to the display on the GTS.

      Immobiliser
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door Courtesy SW Driver side courtesy switch signal / ON or OFF

      ON: Driver side door open

      OFF: Driver side door closed

      		 -
      Key SW Unlock warning switch signal / ON or OFF

      ON: Key in ignition key cylinder

      OFF: No key in ignition key cylinder

      		 -
      IG SW Ignition switch signal / ON or OFF

      ON: Ignition switch ON or engine started

      OFF: Ignition switch ACC or off

      		 -
      Immobiliser Immobiliser system status / Set or Unset

      Set: No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to ACC or off

      Unset: Key in ignition key cylinder

      		 -
      Response Transponder chip data / NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Frame Error Transponder chip data / NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Different Serial Number Transponder chip data / NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Different Encrypt Code Transponder chip data / NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Abnormal Status Transponder chip data / NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Bcc Malfunction Transponder chip data / NG or OK

      NG: Incorrect data being sent

      OK: Correct data being sent

      		 -
      Sub Key Sub key ID code signal / Reg or Unreg

      Reg: Registered sub key ID code sent

      Unreg: Unmatching sub key ID code sent

      		 -
      Master Key Master key ID code signal / Reg or Unreg

      Reg: Registered master key ID code sent

      Unreg: Unmatching master key ID code sent

      		 -
      Transponder S-Code Number of registered sub key / min. 0, max. 15 Number of registered sub key -
      Transponder M-Code Number of registered master key / min. 0, max. 15 Number of registered master key -
      Reg Code Space Full Memory space for key codes registration / NOT FULL or FULL

      NOT FULL: Key code registration possible

      FULL: Key code registration not possible

      		 -
      +B Power source / Break or Normal

      Break: Power source open

      Normal: Power source normal

      		 -
      Antenna Coil Status Transponder key coil condition / Normal or Fail

      Normal: Antenna coil normal

      Fail: Antenna coil malfunctioning

      		 -
      EEPROM Status EEPROM status / NG or OK

      NG: EEPROM malfunctioning

      OK: EEPROM normal

      		 -
      E/G Start Permission Engine start permission / NG or OK

      NG: Engine start not permitted

      OK: Engine start permitted

      		 -
      Immobi ECU Comm Spd Immobiliser ECU communication speed / Unknown, 50bps, 200bps or No Res

      Unknown: ECU communication speed unknown

      50bps: ECU communication speed 50 bps

      200bps: ECU communication speed 200 bps

      No Res: No ECU communication response

      		 -
      The Number of DTCs Number of DTCs / Min.: 0, Max.: 255 Number of stored DTCs -

      Tech Tips

      Data from an actual vehicle provided for reference.

      A01BAGXE05

      • *1: Insert a key into the ignition key cylinder and turn the ignition switch to ACC.

      • *2: Turn the ignition switch to ON.

      • *3: Turn the ignition switch off and remove the key from the ignition key cylinder.

    6. Enter the following menus: Powertrain / Engine and ECT / Data List.

    7. Read the Data List according to the display on the GTS.

      Engine and ECT
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Immobiliser Fuel Cut Status of immobiliser system fuel cut / ON or OFF

      ON: Immobiliser fuel cut on

      OFF: Immobiliser fuel cut off

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Immobiliser / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Immobiliser
      Tester Display Test Part Control Range Diagnostic Note
      Security Indicator Security indicator light ON/OFF -