ENGINE IMMOBILISER SYSTEM TERMINALS OF ECU


  1. CHECK TRANSPONDER KEY AMPLIFIER


    1. Disconnect the H43 transponder key amplifier connector.

      A01BBQLE06

    2. Measure the resistance of the wire harness side connector.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      AGND (H43-7) - Body ground GR - Body ground Ground Always Below 1 Ω

    3. Reconnect the H43 transponder key amplifier connector.

    4. Measure the resistance and voltage of the connector.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      AGND (H43-7) - Body ground GR - Body ground Ground Always Below 1 Ω
      VC5 (H43-1) - AGND (H43-7) V - GR Power source No key in ignition key cylinder Below 1 V
      Key inserted 4.6 to 5.4 V
      CODE (H43-4) - AGND (H43-7) L - GR Demodulated signal of key code data No key in ignition key cylinder Below 1 V
      Key inserted

      Pulse generation

      (see waveform 1)
      TXCT (H43-5) - AGND (H43-7) Y - GR Key code output signal No key in ignition key cylinder Below 1 V
      Key inserted

      Pulse generation

      (see waveform 2)

    5. Inspect using an oscilloscope.


      1. A01BAVLE01

        Waveform 1

        Item Content
        Symbols (Terminal No.) CODE (H43-4) - AGND (H43-7)
        Tool Setting 2 V/DIV., 20 msec./DIV.
        Condition Key inserted
      2. A01BH0KE01

        Waveform 2

        Item Content
        Symbols (Terminal No.) TXCT (H43-5) - AGND (H43-7)
        Tool Setting 2 V/DIV., 20 msec./DIV.
        Condition Key inserted

  2. CHECK TRANSPONDER KEY ECU


    1. Disconnect the H60 transponder key ECU connector.

      A01BF8QE28

    2. Measure the voltage and resistance of the wire harness side connector.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      AGND (H60-5) - Body ground GR - Body ground Ground Always Below 1 Ω
      GND (H60-16) - Body ground W-B - Body ground Ground Always Below 1 Ω
      +B (H60-1) - GND (H60-16) W-R - W-B Power source supply Always 11 to 14 V
      IG (H60-2) - GND (H60-16) B-R - W-B Ignition power supply Ignition switch OFF Below 1 V
      Ignition switch ON 11 to 14 V
      KSW (H60-3) - GND (H60-16) Y - W-B Unlock warning switch No key in ignition key cylinder 10 kΩ or higher
      Key inserted Below 1 Ω

    3. Reconnect the H60 transponder key ECU connector.

    4. Measure the voltage of the connector.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      VC5 (H60-14) - AGND (H60-5) V - GR Power source of transponder key amplifier No key in ignition key cylinder Below 1 V
      Key is inserted 4.6 to 5.4 V
      CODE (H60-15) - AGND (H60-5) L - GR Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V
      Key is inserted

      Pulse generation

      (see waveform 1)
      TXCT (H60-4) - AGND (H60-5) Y - GR Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V
      Key is inserted

      Pulse generation

      (see waveform 2)
      EFIO (H60-13) - GND (H60-16) B-W - W-B ECM output signal Ignition switch OFF Below 1 V
      Ignition switch ON

      Pulse generation

      (see waveform 3)
      EFII (H60-12) - GND (H60-16) W-R - W-B ECM input signal Ignition switch OFF 11 to 14 V
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

      Pulse generation

      (see waveform 4)

    5. Inspect using an oscilloscope.


      1. A01BAVLE01

        Waveform 1

        Item Content
        Symbols (Terminal No.) CODE (H60-15) - AGND (H60-5)
        Tool Setting 2 V/DIV., 20 msec./DIV.
        Condition Key inserted
      2. A01BH0KE01

        Waveform 2

        Item Content
        Symbols (Terminal No.) TXCT (H60-4) - AGND (H60-5)
        Tool Setting 2 V/DIV., 20 msec./DIV
        Condition Key inserted
      3. A01BA5ZE01

        Waveform 3

        Item Content
        Symbols (Terminal No.) EFIO (H60-13) - GND (H60-16)
        Tool Setting 10 V/DIV., 100 msec./DIV.
        Condition Ignition switch ON
      4. A01BD89E01

        Waveform 4

        Item Content
        Symbols (Terminal No.) EFII (H60-12) - GND (H60-16)
        Tool Setting 5 V/DIV., 500 ms/DIV.
        Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

  3. CHECK ECM (2TR-FE, 1TR-FE)

    A01BAVCE07

    1. Measure the voltage and resistance of the connectors.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      IMI (B7-16) - E01 (D1-7) B-W - W-B Transponder key ECU input signal Ignition switch OFF Below 1 V
      Ignition switch ON

      Pulse generation

      (see waveform 1)
      IMO (B7-15) - E01 (D1-7) W-R -W-B Transponder key ECU output signal Ignition switch OFF 11 to 14 V
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

      Pulse generation

      (see waveform 2)
      E01 (D1-7) - Body ground W-B - Body ground Ground Always Below 1 Ω
      E02 (D1-6) - Body ground W-B - Body ground Ground Always Below 1 Ω
      EC (B9-22) - Body ground W-B - Body ground Ground Always Below 1 Ω

    2. Inspect using an oscilloscope.


      1. A01BA5ZE01

        Waveform 1

        Item Content
        Symbols (Terminal No.) IMI (B7-16) - E01 (D1-7)
        Tool Setting 10 V/DIV., 100 msec./DIV.
        Condition Ignition switch ON
      2. A01BD89E01

        Waveform 2

        Item Content
        Symbols (Terminal No.) IMO (B7-15) - E01 (D1-7)
        Tool Setting 5 V/DIV., 500 msec./DIV.
        Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

  4. CHECK ECM (1KD-FTV)

    A01BB3VE01

    1. Measure the voltage and resistance of the connectors.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      IMI (B47-28) - E01 (D70-12) B-W - BR Transponder key ECU input signal Ignition switch OFF Below 1 V
      Ignition switch ON

      Pulse generation

      (see waveform 1)
      IMO (B47-29) - E01 (D70-12) W-R - BR Transponder key ECU output signal Ignition switch OFF 11 to 14 V
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

      Pulse generation

      (see waveform 2)
      E01 (D70-12) - Body ground BR - Body ground Ground Always Below 1 Ω
      E02 (D70-13) - Body ground BR - Body ground Ground Always Below 1 Ω

    2. Inspect using an oscilloscope.


      1. A01BA5ZE01

        Waveform 1

        Item Content
        Symbols (Terminal No.) IMI (B47-28) - E01 (D70-12)
        Tool Setting 10 V/DIV., 100 msec./DIV.
        Condition Ignition switch ON
      2. A01BD89E01

        Waveform 2

        Item Content
        Symbols (Terminal No.) IMO (B47-29) - E01 (D70-12)
        Tool Setting 5 V/DIV., 500 msec./DIV.
        Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

  5. CHECK ECM (2KD-FTV)

    A01BAVCE07

    1. Measure the voltage and resistance of the connectors.

      Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition
      IMI (B7-30) - E01 (D1-7) B-W - BR Transponder key ECU input signal Ignition switch OFF Below 1 V
      Ignition switch ON

      Pulse generation

      (see waveform 1)
      IMO (B7-29) - E01 (D1-7) W-R - BR Transponder key ECU output signal Ignition switch OFF 11 to 14 V
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.

      Pulse generation

      (see waveform 2)
      E01 (D1-7) - Body ground BR - Body ground Ground Always Below 1 Ω
      E02 (D1-6) - Body ground BR - Body ground Ground Always Below 1 Ω

    2. Inspect using an oscilloscope.


      1. A01BA5ZE01

        Waveform 1

        Item Content
        Symbols (Terminal No.) IMI (B7-30) - E01 (D1-7)
        Tool Setting 10 V/DIV., 100 msec./DIV.
        Condition Ignition switch ON
      2. A01BD89E01

        Waveform 2

        Item Content
        Symbols (Terminal No.) IMO (B7-29) - E01 (D1-7)
        Tool Setting 5 V/DIV., 500 msec./DIV.
        Condition Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.