REAR SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL NO.4 SEAT BELT ASSEMBLY OUTER


    1. A01BDVH

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

    2. A01BAOA

      Install the No.4 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01BHXU

      Engage the 4 claws to install the retractor cover of the No.4 seat belt assembly outer.

    4. A01BGFF

      Connect the shoulder side of the No.4 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. A01BCNU

      Engage the 2 claws to install the shoulder side cover of the No.4 seat belt assembly outer.

    6. A01BBPR

      Connect the floor side of the No.4 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Check if the ELR locks.

      Note

      This check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the outer belt assembly.

  2. INSTALL NO.3 SEAT BELT ASSEMBLY OUTER


    1. A01BD39

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

    2. A01BCED

      Install the No.3 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01BE7O

      Engage the 4 claws to install the retractor cover of the No.3 seat belt assembly outer.

    4. A01BCWA

      Connect the shoulder side of the No.3 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. A01BEOL

      Engage the 4 claws to install the retractor cover of the No.3 seat belt assembly outer.

    6. A01BHKL

      Connect the floor side of the No.3 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Check if the ELR locks.

      Note

      This check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the outer belt assembly.

  3. INSTALL REAR NO.2 SEAT BELT ASSEMBLY OUTER


    1. A01BH70

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

    2. A01BCQQ

      Install the rear No.2 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01BACW

      Connect the shoulder side of the rear No.2 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. A01BGW6

      Engage the 2 claws to install the retractor cover of the rear No.2 seat belt assembly outer.

    5. A01BFZF

      Connect the floor side of the rear No.2 seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. Check if the ELR locks.

      Note

      This check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the outer belt assembly.

  4. INSTALL REAR SEAT BELT ASSEMBLY OUTER


    1. A01BFR1

      Check the degree of tilt when the ELR begins to lock.


      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

    2. A01BDAM

      Install the rear seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01BFZ5

      Connect the shoulder side of the rear seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. A01BEOJ

      Engage the 4 claws to install the retractor cover of the rear seat belt assembly outer.

    5. A01BF9V

      Connect the floor side of the rear seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. for Rear No. 1 Seat Bench Seat Type:


      1. A01BB9B

        Check the degree of tilt when the ELR begins to lock.

        Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt when gently moving the installed retractor.

        Note

        Do not disassemble the retractor.

        If operation is not as specified, replace the rear seat belt assembly outer.

      2. A01BCS5

        Temporarily install the rear seat belt assembly outer with the 2 bolts.

      3. Tighten the lower side bolt first, and then tighten the upper side bolt to install the rear seat belt assembly outer.

        Torque:
        for Upper Bolt
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
        for Lower Bolt
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      4. A01BEHE

        Engage the 2 claws to install the retractor cover of the rear seat belt assembly.

      5. Tighten the bolt.

        Torque:
        8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
      6. A01BB4S

        Connect the shoulder side of the rear seat belt assembly outer with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      7. A01BH1T

        Engage the 2 claws to install the shoulder side cover of the rear seat belt assembly outer.

      8. A01BI1V

        Connect the floor side of the rear seat belt assembly outer with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Check if the ELR locks.

      Note

      This check should be performed with the rear seat belt assembly outer installed.


      1. With the rear seat belt assembly outer installed, check that the belt locks when it is pulled out quickly.

        If operation is not as specified, replace the rear seat belt assembly outer.

  5. INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.4 Seat Assembly)


    1. A01BG7A

      Install the rear seat 3 point type belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Install the 3 screws.

  6. INSTALL REAR SEAT SHOULDER BELT HOLE COVER (for Rear No.4 Seat Assembly)

  7. INSTALL REAR SEAT CUSHION SHIELD INNER NO.1 (for Rear No.4 Seat Assembly)

  8. INSTALL NO.4 SEATBACK COVER SUB-ASSEMBLY WITH PAD (for Rear No.4 Seat Assembly)

  9. INSTALL REAR SEATBACK LOCK BEZEL LOWER (for Rear No.4 Seat Assembly)

  10. INSTALL REAR SEATBACK LOCK BEZEL UPPER (for Rear No.4 Seat Assembly)

  11. INSTALL REAR SEAT HEADREST SUPPORT (for Rear No.4 Seat Assembly)

  12. INSTALL REAR SEAT CUSHION (for Rear No.4 Seat Assembly)

  13. INSTALL REAR SEAT HEADREST ASSEMBLY (for Rear No.4 Seat Assembly)

  14. INSTALL NO.4 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD (for Rear No.4 Seat Assembly)


    1. A01BGK4

      Install the No.4 seat cushion cover sub-assembly with pad with the hook and 2 clips.

    2. A01BE1J

      Install the No.4 seat cushion assembly with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  15. CONNECT REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.4 Seat Assembly)


    1. Connect the rear seat 3-point type belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  16. INSTALL LAP BELT OUTER ANCHOR COVER (for Rear No.4 Seat Assembly)

  17. INSTALL RECLINING ADJUSTER COVER RH (for Rear No.4 Seat Assembly)

  18. INSTALL RECLINING ADJUSTER COVER LH (for Rear No.4 Seat Assembly)

  19. INSTALL RECLINING ADJUSTER RELEASE HANDLE (for Rear No.4 Seat Assembly)

  20. INSTALL NO.4 SEAT LEG BRACKET REAR (for Rear No.4 Seat Assembly)


    1. A01BABO

      Install the No.4 seat leg bracket rear with the bolt and spacer.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  21. INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.2 Seat Assembly)


    1. A01BHZC

      Install the rear seat 3 point type belt assembly with the 2 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Install the 4 screws.

  22. INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (for Rear No.3 Seat Assembly)


    1. A01BA59

      Install the 2 rear seat 3 point type belt assemblies with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Install the 8 screws.

  23. INSTALL NO.2 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD (for Rear No.2 Seat Assembly)

  24. INSTALL NO.3 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD (for Rear No.3 Seat Assembly)

  25. INSTALL RECLINING ADJUSTER COVER LH (for Rear No.2 Seat Assembly)

  26. INSTALL RECLINING ADJUSTER COVER LH (for Rear No.3 Seat Assembly)

  27. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 LH (for Rear No.2 Seat Assembly)

  28. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.3 LH (for Rear No.3 Seat Assembly)

  29. INSTALL REAR SEAT BELT ASSEMBLY INNER (for Rear No.2 Seat Assembly)

    Tech Tips

    Follow the same procedure as for the rear No.2 seat assembly.

  30. INSTALL REAR SEAT BELT ASSEMBLY INNER (for Rear No.3 Seat Assembly)

    Tech Tips

    Follow the same procedure as for the rear No.2 seat assembly.

  31. INSTALL RECLINING ADJUSTER COVER RH (for Rear No.2 Seat Assembly)

  32. INSTALL RECLINING ADJUSTER COVER RH (for Rear No.3 Seat Assembly)

  33. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 RH (for Rear No.2 Seat Assembly)

  34. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.3 RH (for Rear No.3 Seat Assembly)

  35. INSTALL REAR SEAT BELT ASSEMBLY OUTER (for Swiveling Seat Type)


    1. Install the rear seat belt assembly outer with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  36. INSTALL REAR SEAT TURN TABLE COVER (for Swiveling Seat Type)

  37. INSTALL SEAT TRACK ADJUSTING HANDLE KNOB (for Swiveling Seat Type)

  38. INSTALL RECLINING ADJUSTER COVER RH (for Swiveling Seat Type)

  39. INSTALL RECLINING ADJUSTER COVER LH (for Swiveling Seat Type)

  40. INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.1 (for Swiveling Seat Type)

  41. INSTALL REAR NO.4 SEAT ASSEMBLY


    1. A01BD6D

      Secure the rear No.4 seat assembly with the 2 locks

    2. Install the rear No.4 seat assembly with the 3 bolts and 2 nuts.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

      Note

      After installing the rear No.4 seat assembly, fold down the seatback onto the seat cushion, lift the side of the rear No.4 seat assembly, and drop it to engage the locks securely.

  42. INSTALL REAR NO.3 SEAT ASSEMBLY

    for Bench Type Seatback Click here

    for Separate Type Seatback Click here

  43. INSTALL REAR NO.2 SEAT ASSEMBLY

    w/o Headrest Click here

    w/ Headrest Click here

  44. INSTALL REAR NO.1 SEAT ASSEMBLY

    w/o Headrest Click here

    w/ Headrest Click here