COMPRESSOR AND MAGNETIC CLUTCH (for 1KD-FTV, 2KD-FTV) INSTALLATION

INSTALL COMPRESSOR AND MAGNETIC CLUTCH
1. Provisionally tighten the compressor and magnetic clutch with the 4 bolts.
2. Tighten the compressor and magnetic clutch with the 4 bolts.
  
  Torque:
  
  25 N*m { 255 kgf*cm, 18 ft.*lbf }
  
  Note
  
  Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.
INSTALL COOLER REFRIGERANT NO. 1 SUCTION HOSE
1. Remove the attached vinyl tape from the hose.
2. Apply sufficient compressor oil (ND-OIL 8) to a new O-ring and the fitting surface of the compressor and magnetic clutch.
  
  Compressor oil
  
  ND-OIL 8 or equivalent
3. Install the O-ring onto the cooler refrigerant suction hose.
4. Install the cooler refrigerant suction hose onto the compressor and magnetic clutch with the bolt.
  
  Torque:
  
  9.8 N*m { 100 kgf*cm, 87 in.*lbf }
INSTALL COOLER REFRIGERANT NO. 1 DISCHARGE HOSE
1. Remove the attached vinyl tape from the hose.
2. Apply sufficient compressor oil (ND-OIL 8) to a new O-ring and the fitting surface of the compressor and magnetic clutch.
  
  Compressor oil
  
  ND-OIL 8 or equivalent
3. Install the O-ring onto the cooler refrigerant discharge hose.
4. Install the cooler refrigerant discharge hose onto the compressor and magnetic clutch with the bolt.
  
  Torque:
  
  9.8 N*m { 100 kgf*cm, 87 in.*lbf }
INSTALL FAN & GENERATOR V BELT (for 1KD-FTV)
1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.
  
  Note
  
  Make sure that the fan and generator V belt is set properly on each pulley.
2. Check that the indicator mark of the V-ribbed belt tensioner Click here.
INSTALL FAN & GENERATOR V BELT (for 2KD-FTV)
1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.
  
  Note
  
  Make sure that the fan and generator V belt is set properly on each pulley.
2. Check that the indicator mark of the V-ribbed belt tensioner Click here.
INSTALL NO. 1 ENGINE UNDER COVER (w/ Engine Under Cover Assembly)

Torque:

13 N*m { 133 kgf*cm, 10 ft.*lbf }
INSTALL ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
1. Install the engine service hole sub cover with the 5 bolts.
  
  Torque:
  
  13 N*m { 133 kgf*cm, 10 ft.*lbf }
INSTALL FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)
1. Connect the front seat inner belt assembly connector and install the front seat assembly.
2. Align the front seat assembly adjuster pin with the holes in the body.
3. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
4. Temporarily tighten the 2 bolts on the front side of the front seat assembly.
5. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
6. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.
7. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
8. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
9. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
10. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
INSTALL FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)
1. Connect the front seat inner belt assembly connector and install the front seat assembly.
2. Align the front seat assembly adjuster pin with the holes in the body.
3. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
4. Temporarily tighten the 2 bolts on the front side of the front seat assembly.
5. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
6. Temporarily tighten the 2 bolts on the rear side of the front seat assembly.
7. Move the front seat assembly to the rearmost position.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
8. Fully tighten the 2 bolts on the front side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
9. Move the front seat assembly fully forward.
  
  Note
  
  Make sure that the front seat assembly is securely locked.
10. Fully tighten the 2 bolts on the rear side of the front seat assembly in the order of outer and inner side.
  
  Torque:
  
  39 N*m { 398 kgf*cm, 29 ft.*lbf }
INSTALL FRONT DOOR SCUFF PLATE RH

Compressor oil
ND-OIL 8 or equivalent

Compressor oil
ND-OIL 8 or equivalent

CHARGE REFRIGERANT

Perform vacuum purging using a vacuum pump.

Charge with refrigerant HFC-134a (R134a).

Standard
Single A/C
520 to 580g (18.3 to 20.5 oz.)
Dual A/C
670 to 730g (23.0 to 25.7 oz.)

SST: 07110-58060 ( 07117-58090, 07117-78050, 07117-58070, 07117-58060, 07117-58080, 07117-88060, 07117-88070, 07117-88080 )

Note

Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant, which causes the compressor to overheat.
Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

Tech Tips

Prepare a service can to recharge refrigerant if using the refrigerant gas collected with the freon collection/recycling device because the collective rate of the device is approximately 90%.

WARM UP ENGINE
1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.
  
  Note
  
  Be sure to warm up the compressor when turning the A/C switch on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.
CHECK FOR LEAKAGE OF REFRIGERANT
1. After recharging refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.
2. Carry out the test under the following conditions:
  - Stop the engine.
  - Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
  - Repeat the test 2 or 3 times.
  - Make sure that there is some refrigerant remaining in the refrigeration system.
    
    When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm², 57 to 85 psi)
3. Using a gas leak detector, check for leakage of the refrigerant line.
4. Bring the gas leak detector close to the drain hose with the detector's power off.
  Tech Tips
  
  After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
  
  Bring the gas leak detector sensor under the drain hose.
  
  When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
  
  If such reaction is unavoidable, the vehicle must be lifted up.
5. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.
6. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.