REAR BRAKE REMOVAL


  1. REMOVE REAR WHEEL

  2. DRAIN BRAKE FLUID

    Note

    Wash off brake fluid immediately if it comes in contact with any painted surface.

  3. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY


    1. Release the parking brake lever, and remove the brake drum.

      A01BDC8E01
      Text in Illustration
      *A for 295 mm Drum *B for 254 mm Drum

      Tech Tips

      If the brake drum cannot be removed easily, perform the following steps.

    2. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

    3. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.

  4. REMOVE REAR AXLE BRAKE DRUM GASKET

  5. REMOVE AUTOMATIC ADJUST LEVER


    1. for 254 mm drum:


      1. A01BDIP

        Remove the automatic adjust lever and the tension spring.

  6. SEPARATE PARKING BRAKE SHOE STRUT SET


    1. for 254 mm drum:


      1. A01BBSLE01

        Using SST, remove the upper side tension spring from the brake shoe.

        SST
        09703-30011

    2. for 295 mm drum:


      1. A01BI5UE01

        Using SST, remove the upper side tension spring from the brake shoe.

        SST
        09703-30011

  7. REMOVE FRONT BRAKE SHOE


    1. for 254 mm drum:


      1. A01BGIR

        Using a needle-nose pliers, remove the anchor side tension spring.

      2. A01BANUE01

        Using SST, remove the cup, shoe hold-down sprig and pin.

        SST
        09718-00011
      3. A01BDX5E02
        Text in Illustration
        *A LH Side
        *B RH Side

        Remove the parking brake shoe lower strut.

      4. Separate the brake shoe return spring, and remove the front brake shoe.

    2. for 295 mm drum:


      1. A01BCHME01

        Using SST, remove the cup, shoe hold-down sprig and pin.

        SST
        09718-00011

      2. Separate the brake shoe return spring, and remove the front brake shoe.

  8. REMOVE REAR BRAKE SHOE


    1. for 254 mm drum:


      1. A01BHHPE01

        Using SST, remove the cup, shoe hold-down sprig and pin.

        SST
        09718-00011
      2. A01BBA3

        Disconnect the parking brake cable No. 3 and remove the rear brake shoe.

    2. for 295 mm drum:


      1. A01BE8GE01

        Using SST, remove the cup, shoe hold-down sprig and pin.

        SST
        09718-00011

      2. Remove the tension spring.

      3. A01BEF9

        Disconnect the parking brake cable No. 3 and remove the rear brake shoe.

  9. REMOVE PARKING BRAKE SHOE STRUT SET


    1. for 254 mm drum:


      1. A01BFWHE02
        Text in Illustration
        *1 Brake Shoe Lever
        *2 Brake Shoe Strut Set
        *3 Rear Brake Shoe
        *4 Rear Cushion Lever
        *5 C-washer

        Using a screwdriver, remove the C-washer, brake shoe lever, rear cushion lever and brake shoe strut set from the brake shoe.

      2. Remove the adjusting bolt and tension spring from the brake shoe strut set.

    2. for 295 mm drum:


      1. A01BCYWE01
        Text in Illustration
        *1 Rear Brake Shoe
        *2 Brake Shoe Strut Set
        *3 Brake Shoe Lever
        *4 Automatic Adjust Lever
        *5 C-washer
        *6 E-ring

        Remove the brake shoe strut set.

      2. Using a screwdriver, remove the E-ring and automatic adjust lever.

      3. Using a screwdriver, remove the C-washer and brake shoe lever from the brake shoe.

  10. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY


    1. A01BH8I

      Using a union nut wrench, disconnect the brake tube, use a container to catch brake fluid.

    2. Remove the 2 bolts and wheel cylinder.

  11. REMOVE REAR WHEEL BRAKE CYLINDER CUP KIT


    1. Remove the 2 cylinder dust boots from the wheel cylinder.

    2. Remove the 2 pistons.

    3. Remove the 2 cylinder cups from each piston.

    4. Remove the compression spring.

  12. REMOVE REAR DRUM BRAKE BLEEDER PLUG