REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL


  1. REMOVE REAR WHEELS

  2. DRAIN DIFFERENTIAL OIL


    1. Remove the filler plug and gasket.

    2. Remove the drain plug and gasket, and drain the oil.

  3. DRAIN BRAKE FLUID

  4. REMOVE REAR BRAKE DRUM SUB-ASSEMBLIES


    1. A01BF75E01

      Release the parking brake lever, and remove the brake drum.

      Tech Tips

      If the brake drum cannot be removed easily, perform the following steps.

    2. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

    3. Using another screwdriver, contract the brake shoe adjuster by turning the adjusting wheel.

  5. REMOVE REAR AXLE BRAKE DRUM GASKETS

  6. REMOVE AUTOMATIC ADJUST LEVER LH


    1. A01BDIP

      Remove the automatic adjust lever and the tension spring.

  7. REMOVE AUTOMATIC ADJUST LEVER RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  8. SEPARATE PARKING BRAKE SHOE STRUT SET LH


    1. A01BHY6E01

      Using SST, remove the upper side tension spring from the brake shoe.

      SST
      09703-30011

  9. SEPARATE PARKING BRAKE SHOE STRUT SET RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  10. REMOVE FRONT BRAKE SHOES


    1. A01BGIR

      Using a needle-nose pliers, remove the anchor side tension spring.

    2. A01BANUE01

      Using SST, remove the cup, shoe hold-down sprig and pin.

      SST
      09718-00010
    3. A01BDX5E01

      Remove the parking brake shoe lower strut.

    4. Separate the brake shoe return spring, and remove the front brake shoe.

  11. REMOVE REAR BRAKE SHOES


    1. A01BHHPE01

      Using SST, remove the cup, shoe hold-down sprig and pin.

      SST
      09718-00010
    2. A01BBA3

      Disconnect the parking brake cable No.3 and remove the rear brake shoe.

  12. REMOVE PARKING BRAKE SHOE STRUT SET LH


    1. A01BFWHE01

      Using a screwdriver, remove the C-washer, brake shoe lever, rear cushion lever and brake shoe strut set from the brake shoe.

    2. Remove the adjusting bolt and tension spring from the brake shoe strut set.

  13. REMOVE PARKING BRAKE SHOE STRUT SET RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  14. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO. 3


    1. A01BAUJ

      Remove the 2 bolts and separate the parking brake cable assembly No.3 from the rear brake backing plate.

  15. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO. 2

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  16. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY LH


    1. A01BH8I

      Using SST, disconnect the brake tube, use a container to catch brake fluid.

      SST
      09023-00101

    2. Remove the 2 bolts and wheel cylinder.

  17. REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  18. SEPARATE SPEED SENSOR REAR LH (w/ ABS)


    1. A01BAZUE01

      Remove the bolt and separate the rear speed sensor.

      Note


      • Prevent foreign matter from adhering to the speed sensor.

      • Be careful not to damage the speed sensor.

    2. Remove the O-ring from the rear speed sensor.

  19. SEPARATE SPEED SENSOR REAR RH (w/ ABS)

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  20. REMOVE REAR AXLE SHAFT WITH BACKING PLATE LH


    1. A01BG26J01

      Remove the 4 nuts and rear axle shaft with backing plate.

      Note


      • Be careful not to damage the rear axle shaft oil seal.

      • Be careful not to damage the skid control rotor rear.

  21. REMOVE REAR AXLE SHAFT WITH BACKING PLATE RH

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  22. REMOVE BEARING RETAINER O-RINGS


    1. Remove the bearing retainer O-ring from the rear axle housing assembly.

  23. REMOVE REAR AXLE SHAFT LH OIL SEAL


    1. A01BB6AE01

      Using SST, remove the rear axle shaft oil seal from the rear axle housing assembly.

      SST
      09308-00010

  24. REMOVE REAR AXLE SHAFT RH OIL SEAL

    Tech Tips

    Removal procedure of the RH side is the same as that of the LH side.

  25. REMOVE PROPELLER SHAFT ASSEMBLY (for Super Long Wheelbase)


    1. A01BHYPE01

      Put matchmarks on both flanges.

    2. Remove the 4 nuts, bolts and washers.

      Tech Tips

      If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller with center bearing shaft assembly from the differential companion flange.

    3. A01BGNF

      Remove the 2 bolts and center support bearing assembly No.1.

    4. Remove the propeller with center bearing shaft assembly.

    5. A01BGHTE01

      Insert SST in the transmission to prevent oil leakage.

      Note

      Do not damage the oil seal.


      1. Use the following SST for the automatic transmission.

        SST
        09325-40010

      2. Use the following SST for the manual transmission.

        SST
        09325-20010

  26. REMOVE PROPELLER SHAFT ASSEMBLY (for Long Wheelbase)


    1. A01BHYPE01

      Put matchmarks on both flanges.

    2. Remove the 4 nuts, bolts and washers.

      Tech Tips

      If the flange connection is hard to separate, temporarily tighten one nut only and evenly tap the flange with a brass bar and hammer to separate the propeller shaft assembly from the differential companion flange.

    3. Remove the propeller shaft assembly.

    4. A01BGHTE01

      Insert SST in the transmission to prevent oil leakage.

      Note

      Do not damage the oil seal.


      1. Use the following SST for the automatic transmission

        SST
        09325-40010

      2. Use the following SST for the manual transmission

        SST
        09325-20010

  27. DISCONNECT LOAD SENSING BRACKET


    1. A01BGO6

      Remove the 2 nuts and load sensing bracket.

  28. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY


    1. Support the differential carrier assembly with a jack.

      Note

      Do not drop the differential carrier assembly

    2. A01BC5ZE01

      Remove the 10 nuts, washers and differential carrier assembly.

      Note


      • Do not damage the installation surface when removing the differential carrier assembly.

      • The remaining oil may leak out when removing the differential carrier assembly.

  29. REMOVE REAR DIFFERENTIAL CARRIER GASKET