AUTOMATIC TRANSMISSION ASSEMBLY (for 1KD-FTV) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE TRANSMISSION OIL LEVEL GAUGE SUB-ASSEMBLY


    1. A01BH56

      Remove the transmission oil level gauge sub-assembly from the transmission oil filler tube sub-assembly.

  3. DRAIN AUTOMATIC TRANSMISSION FLUID


    1. A01BA6FE01

      Remove the drain plug and gasket and drain automatic transmission fluid.

    2. Install the drain plug with a new gasket.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  4. REMOVE PROPELLER SHAFT ASSEMBLY

    Click here

  5. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. A01BBS3

      Remove the 2 bolts, 2 nuts and 2 compression springs.

    2. Disconnect the No. 4 exhaust pipe support and front exhaust pipe.

    3. Remove the 2 gaskets.

  6. REMOVE TURBINE OUTLET ELBOW STAY


    1. A01BGMC

      Remove the 2 bolts, 2 nuts and turbine outlet elbow stay.

  7. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


    1. A01BAMN

      Remove the 3 nuts, exhaust manifold converter and gasket.

  8. REMOVE STARTER ASSEMBLY


    1. A01BG1IE01

      for Wide Body:

      Remove the bolt, then disconnect the ground cable.

    2. A01BBCCE01

      Open the terminal cap.

    3. Remove the nut and disconnect the wire harness from terminal 30.

    4. Disconnect the terminal 50 connector from the starter.

    5. A01BBX7

      for Automatic Transmission:

      Remove the bolt and 2 nuts, then remove the starter.

    6. A01BDA6

      for Manual Transmission:

      Remove the bolt and nut, then remove the starter.

  9. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY


    1. A01BBQWE02

      Remove the 2 bolts and transmission oil filler tube sub-assembly.

    2. Remove the O-ring from the oil filler tube sub-assembly.

  10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A01BDE0E03

      Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever assembly.

    2. Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.

  11. DISCONNECT OIL COOLER TUBE


    1. Remove the 5 bolts and disconnect the 3 oil cooler tube clamps.

      A01BH54
    2. A01BGB1

      Using a 17 mm union nut wrench, disconnect the 2 oil cooler tubes from each oil cooler tube union.

  12. DISCONNECT CONNECTOR


    1. A01BAFZE03

      Disconnect the park/neutral position switch connector and temperature sensor connector.

    2. A01BH1G

      Disconnect the speedometer sensor connector.

    3. A01BDUEE04

      Disconnect the No. 2 vehicle speed sensor connector and transmission wire connector.

    4. A01BB1LE02

      Disconnect the overdrive direct clutch speed sensor connector.

  13. DISCONNECT WIRE HARNESS


    1. A01BAAW

      Remove the 2 bolts and disconnect the wire harness from the automatic transmission assembly.

  14. REMOVE NO. 4 CYLINDER BLOCK INSULATOR


    1. A01BH4VE02

      Remove the No. 4 cylinder block insulator.

  15. REMOVE STIFFENER PLATE RH(ATM)


    1. A01BAX5

      Remove the 3 bolts and stiffener plate RH.

  16. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    1. A01BGOBE02

      Remove the bolt and drive plate cover from the automatic transmission assembly.

    2. A01BG9E

      Turn the crankshaft pulley and remove the 6 drive plate and torque converter clutch setting bolts.

  17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


    1. A01BA55

      Support the automatic transmission assembly with a transmission jack.

  18. SEPARATE ENGINE MOUNTING REAR INSULATOR ASSEMBLY


    1. A01BFS5

      Remove the bolt, the nut and the washer and separate the engine mounting rear insulator assembly.

  19. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    1. A01BDRV

      Remove the 5 bolts and automatic transmission assembly.

      Note

      Do not use excess force to pry off the transmission assembly.

  20. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. A01BFFD

      Remove the 2 bolts and the No. 1 transmission control cable bracket from the automatic transmission housing.

  21. REMOVE ENGINE MOUNTING REAR INSULATOR ASSEMBLY


    1. A01BH4E

      Remove the 4 bolts and engine mounting rear insulator assembly from the extension housing sub-assembly.

  22. REMOVE BREATHER PLUG HOSE


    1. A01BD35

      Remove the bolt and breather plug hose from the automatic transmission housing.

  23. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY


    1. A01BHVZE01

      Put a matchmark on the automatic transmission housing and the torque converter clutch assembly.

    2. Remove the torque converter clutch assembly from the automatic transmission assembly.

  24. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY


    1. A01BBP9E02

      Inspect the one-way clutch.


      1. Install the SST so that it fits in the notch of the converter hub and the outer race of the one-way clutch.

        SST
        09350-32014   ( 09351-32010, 09351-32020 )

      2. Install the SST (Stopper) from the sleeve of torque converter assembly and engage serration of stater slight washer.

      3. Stand up the torque converter and turn the SST (tool ).

        SST
        09350-32014   ( 09351-32010, 09351-32020 )
        Standard
        Check if it rotates smoothly when turned clockwise and locks up when turned counter clockwise.
    2. A01BEIEE01

      Determine the condition of the torque converter clutch assembly.


      1. If the inspection result of the torque converter clutch assembly meets the following item, replace the torque converter clutch.

        Malfunction item
        Any metallic sound is heard from the torque converter clutch during stall test or when the shift lever is in the N position.
        The one-way clutch is free or locked in both directions.
        Fine powder exceeding the sample limit is identified in ATF. (See the sample.)

        Tech Tips


        • The sample shows the auto fluid of approximately 0.25 liters (0.26 US qts, 0.22 lmp, qts) that is taken out from the removed torque converter clutch.

    3. Replace the ATF in the torque converter clutch.


      1. If the ATF is discolored and/or has a foul odor, completely stir the ATF in the torque converter clutch and drain it with the installation face up.

    4. A01BBJ5

      Clean and check the oil cooler and oil pipe line.


      1. If the torque converter clutch is inspected or exchange the ATF, is exchanged, clean the oil cooler and oil pipe line.

        Tech Tips


        • Spray compressed air of 196 kPa (2kgf/cm2, 28 psi) from the inlet hose.

        • If plenty of fine powders are identified in the ATF, add a new ATF using a bucket pump and clean it again.

      2. If the ATF is cloudy, inspect the oil cooler.