ELECTRONIC CONTROLLED AUTOMATIC TRANSMISSION SYSTEM, Diagnostic DTC:P0560/96

DTC Code DTC Name
P0560/96 System Voltage

DESCRIPTION

The battery supplies electricity to the TCM even when the ignition switch is off. This power allows the TCM to store data such as DTC history, freeze frame data and etc. If the battery voltage falls below a minimum level, these memories are cleared and the TCM determines that there is a malfunction in the power supply circuit. When the engine is next started, the TCM will illuminate the MIL and set the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560/96

Open in TCM back-up power source circuit.

DTC is detected for 3 sec. or more.

(1-trip detection logic)

  • Open in TCM back-up power source circuit

  • EFI fuse

  • Battery

  • TCM

Tech Tips

If DTC P0560/96 is set, the TCM does not store other DTCs.

WIRING DIAGRAM

A01BE4IE02

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK FUSE (EFI FUSE)


    1. A01BCN3E02

      Remove the EFI fuse from the No. 1 engine room R/B and J/B.

    2. Measure the EFI fuse resistance.

      Standard resistance
      Below 1 Ω

    NG

    CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

    OK

  2. CHECK HARNESS AND CONNECTOR (+B VOLTAGE OF TCM)


    1. Disconnect the TCM connector.

    2. A01BBRJE07

      Measure the voltage of the TCM connector.

      Standard voltage
      Tester Connection Specified Condition
      +B (O3-5) - Body ground 11 to 14 V

    NG

    CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND, TCM - EFI FUSE, EFI FUSE - BATTERY) Click here

    OK

  3. CHECK DTC OUTPUT


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position.

    3. Turn on the tester.

    4. Clear the DTC Click here.

    5. Turn the ignition switch off and turn the tester off.

    6. Start the engine and turn on the tester.

    7. Select the item: "Power train / ECT / DTC / Current or Pending".

    8. Read the DTCs using the intelligent tester.

      Result
      Display (DTC output) Proceed to
      P0560/96 A
      No DTC B

      Tech Tips

      When not using the intelligent tester, refer to DTC CHECK / CLEAR Click here.


    B

    CHECK FOR INTERMITTENT PROBLEMS

    A

    REPLACE TCM

  4. CHECK HARNESS AND CONNECTOR (TCM - BODY GROUND, TCM - EFI FUSE, EFI FUSE - BATTERY)


    1. A01BB2VE34

      Check the harness and the connector between the TCM and body ground.


      1. Disconnect the TCM connector.

      2. Measure the resistance.

        Standard resistance
        Tester Connection Specified Condition
        E1 (O1-1) - Body ground Below 1 Ω
    2. A01BCZ4E01

      Check the harness and the connector between the EFI fuse and TCM.


      1. Remove the EFI fuse from the No. 1 engine room R/B and J/B.

      2. Disconnect the TCM connector.

      3. Measure the resistance.

        Standard resistance (Check for open)
        Tester Connection Specified Condition
        EFI fuse (2) - +B (O3-5) Below 1 Ω
        Standard resistance (Check for short)
        Tester Connection Specified Condition
        EFI fuse (2) or +B (O3-5) - Body ground 10 kΩ or higher

    3. Check the harness and the connector between the EFI fuse and battery.


      1. Remove the EFI fuse from the No. 1 engine room R/B and J/B.

      2. Disconnect the negative battery terminal.

      3. Disconnect the positive battery terminal.

      4. Measure the resistance.

        Standard resistance (Check for open)
        Tester Connection Specified Condition
        Battery positive terminal - EFI fuse (1) Below 1 Ω
        Standard resistance (Check for short)
        Tester Connection Specified Condition
        Battery positive terminal or EFI fuse (1) - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT BATTERY


    1. Check that the battery is not depleted.

      OK
      Battery is not depleted

    NG

    REPLACE BATTERY

    OK

  6. CHECK DTC OUTPUT


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to the ON position.

    3. Turn on the tester.

    4. Clear the DTC Click here.

    5. Turn the ignition switch off and turn the tester off.

    6. Start the engine and turn on the tester.

    7. Select the item: "Power train / ECT / DTC / Current or Pending".

    8. Read the DTCs using the intelligent tester.

      Result
      Display (DTC output) Proceed to
      P0560/96 A
      No DTC B

      Tech Tips

      When not using the intelligent tester, refer to DTC CHECK / CLEAR Click here.


    B

    CHECK FOR INTERMITTENT PROBLEMS

    A

    REPLACE TCM