RADIATOR INSTALLATION


  1. INSTALL RADIATOR ASSEMBLY


    1. A01BC8Q

      Install the radiator assembly to the vehicle.

      Note

      Do not drop the radiator assembly.

  2. INSTALL FAN SHROUD NO.2


    1. A01BHKEJ01

      Install the fan shroud No.2 with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Note

      Do not drop the radiator assembly.

  3. INSTALL FAN SHROUD


    1. A01BB46

      Install the fan shroud with the 6 bolts.

      Torque:
      5.4 N*m  { 53 kgf*cm, 48 in.*lbf }

      Note

      Do not drop the radiator assembly.

    2. Connect the 2 reserve tank hoses.

    3. Connect the 2 radiator hoses.

  4. CONNECT OIL TUBE (for Automatic Transmission)


    1. A01BEH8E01

      Connect the 2 oil tubes to the radiator assembly.

  5. INSTALL COOLING FAN ECU


    1. w/o air conditioning:


      1. Connect the 2connectors to the cooing fan ECU.

      2. A01BGBM

        Install the cooling fan ECU with the 2 bolts and 2 nuts.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. w/ air conditioning:


      1. Connect the 4 connectors to the cooing fan ECU.

      2. A01BGBM

        Install the cooling fan ECU with the 2 bolts and 2 nuts.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  6. INSTALL RADIATOR SUPPORT UPPER


    1. A01BGH0J01

      Install the radiator support upper with the 6 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  7. INSTALL HOOD LOCK ASSEMBLY


    1. Install the hood lock cable assembly to the hood lock assembly.

    2. A01BFC1J01

      Install the hood lock assembly with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  8. INSTALL W/RECEIVER CONDENSER ASSEMBLY (w/ Air Conditioning System)


    1. A01BGR6E01

      Install the w/ receiver condenser assembly with the 4 bolts.

      Note

      Tighten in the order indicated in the illustration.

      Tech Tips

      If the condenser is replaced with a new one, add compressor oil to the new condenser.

      Capacity
      40 cc (1.4fl.oz.)
      Compressor oil
      ND-OIL 8 or equivalent

  9. INSTALL COOLER REFRIGERANT LIQUID PIPE A (w/ Air Conditioning System)


    1. Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.

    2. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

      Compressor oil
      ND-OIL 8 or equivalent

    3. Install the O-ring on the cooler refrigerant liquid pipe A.

    4. A01BFQT

      Install the cooler refrigerant liquid pipe A on the cooler condenser assembly with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 47 in.*lbf }
    5. A01BC7N

      Install the clamp with the bolt.

  10. INSTALL COOLER REFRIGERANT DISCHARGE PIPE A (w/ Air Conditioning System)


    1. Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.

    2. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

      Compressor oil
      ND-OIL 8 or equivalent

    3. Install the O-ring on the cooler refrigerant discharge pipe A.

    4. A01BF96

      Install the cooler refrigerant discharge pipe A on the cooler condenser assembly with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 47 in.*lbf }

  11. INSTALL FRONT BUMPER REINFORCEMENT


    1. A01BBEZ

      Install the front bumper reinforcement with the 6 bolts.

      Torque:
      61 N*m  { 622 kgf*cm, 45 ft.*lbf }

  12. INSTALL FRONT FLOOR CROSS MEMBER REINFORCEMENT SUB-ASSEMBLY RH


    1. A01BEY7E01

      Install the front floor cross member reinforcement sub-assembly with the 5bolts.

      Torque:
      BOLT A
      61 N*m  { 622 kgf*cm, 45 ft.*lbf }
      BOLT B
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  13. INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY


    1. A01BGMOE01

      Install the hood lock support brace sub-assembly with the 3 bolts.

      Torque:
      BOLT A
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
      BOLT B
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  14. INSTALL WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY


    1. Install the windshield washer motor and pump assembly with the 2 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

  15. INSTALL RADIATOR RESERVE TANK ASSEMBLY


    1. Install the radiator reserve tank assembly with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  16. AIRTIGHT CHECK


    1. Apply some soapy water to the junction of the radiator tank lower, radiator tank upper and radiator core.

    2. Remove the radiator reservoir cap.

    3. Attach the radiator cap tester.

    4. Check if the radiator assembly is airtight by pumping the radiator cap tester.

  17. INSTALL RADIATOR SUPPORT SEAL UPPER


    1. A01BBFP

      Install the air inlet duct No.1 with the 6 clamps.

  18. INSTALL FRONT BUMPER

  19. INSTALL STEP PLATE COVER RH

  20. INSTALL STEP PLATE COVER LH

  21. INSTALL RADIATOR GRILLE

  22. ADD ENGINE COOLANT


    1. Firmly tighten the drain plugs and fill the reservoir tank with coolant to the top of the inlet.

    2. Remove the 2-way that is located near the throttle body.

    3. When air is bled and the coolant drains out, firmly install the 2-way.

    4. Add coolant up to the B line mark in the reservoir tank and install the radiator cap.

      Coolant Capacity
      Condition Capacity
      w/ front and rear heaters 13.6 liters (14.4 US qts, 12.0 lmp. qts)
      w/ front heater 11.6 liters (12.3 US qts, 10.2 lmp. qts)
      w/o heater 10.6 liters (11.2 US qts, 9.3 lmp. qts)

    5. Warm up the engine.

    6. After the engine cools down, check that the coolant level is between the LOW and FULL level marks.

  23. CHARGE REFRIGERANT


    1. Perform vacuum purging using a vacuum pump.

    2. Charge with refrigerant HFC-134a (R134a).

      A01BFDKE01
      Standard
      Single A/C
      520 to 580g (18.3 to 20.5 oz.)
      Dual A/C
      670 to 730g (23.0 to 25.7 oz.)
      SST
      07110-58060   ( 07117-58090, 07117-78050, 07117-58070, 07117-58060, 07117-58080, 07117-88060, 07117-88070, 07117-88080 )

      Note


      • Do not operate the cooler compressor before charging refrigerant as the cooler compressor does not work properly without any refrigerant, which causes the compressor to overheat.

      • Approximately 100 g (3.5 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, and not with the sight glass.

      Tech Tips

      Prepare a service can to recharge refrigerant if using the refrigerant gas collected with the freon collection/recycling device because the collective rate of the device is approximately 90%.

  24. WARM UP ENGINE


    1. Warm up the engine at less than 1,850 rpm for 2 minutes or more after charging refrigerant.

      Note

      Be sure to warm up the compressor when turning the A/C switch on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.

  25. CHECK FOR ENGINE COOLANT LEAKS

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

    2. Warm up the engine.

    3. Using a radiator cap tester, increase the pressure inside the radiator to 137 kPa (1.4 kgf/cm2, 19.9 psi), and check that the pressure does not drop.

      Tech Tips

      If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.

  26. CHECK FOR LEAKAGE OF REFRIGERANT


    1. After recharging refrigerant gas, check for leakage of refrigerant gas using a halogen leak detector.

    2. Carry out the test under the following conditions:


      • Stop the engine.

      • Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).

      • Repeat the test 2 or 3 times.

      • Make sure that there is some refrigerant remaining in the refrigeration system.

        When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

    3. A01BC1LE02

      Using a gas leak detector, check for leakage of the refrigerant line.

    4. A01BCXGE01

      Bring the gas leak detector close to the drain hose with the detector's power off.

      Tech Tips


      • After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.

      • Bring the gas leak detector sensor under the drain hose.

      • When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.

        If such reaction is unavoidable, the vehicle must be lifted up.

    5. If a gas leak is not detected on the drain hose, remove the blower motor control from the cooling unit. Insert the gas leak detector sensor into the unit and perform the test.

    6. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.

  27. INSTALL ENGINE UNDER COVER NO.1