FUEL TEMPERATURE SENSOR REMOVAL


  1. REMOVE BATTERY SERVICE HOLE COVER (w/ Sub-Battery)

  2. DISCONNECT BATTERY NEGATIVE CABLE

  3. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)


    1. Perform the same procedure as above on the opposite side. Click here

  4. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)


    1. Perform the same procedure as above on the opposite side. Click here

  5. REMOVE FRONT DOOR SCUFF PLATE RH

  6. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY


    1. Roll up the carpet, and remove the engine service hole sub cover assembly.

  7. REMOVE FAN & GENERATOR V BELT


    1. A01BGLOE03

      Remove the drive belt by rotating the tensioner pulley in clockwise direction to loosen its tension with the pulley set bolt of the tensioner.

  8. SET NO.1 CYLINDER TO TDC/ COMPRESSION


    1. A01BES8E01

      Align the matchmarks of the crankshaft pulley and timing gear case cover by rotating the crankshaft in clockwise direction.

      Tech Tips

      Make sure that both camnoses on the intake side and exhaust side of the cylinder No.1 face upward.

  9. REMOVE TIMING BELT COVER NO.1


    1. Remove the wire harness clamp.

    2. A01BHT6

      Remove the 6 bolts and timing belt cover No.1.

  10. REMOVE TIMING BELT


    1. A01BB9ZE01

      Turn the crankshaft in the clockwise direction and align the timing marks as shown in the illustration.

    2. A01BHFH

      Uniformly loosen the 2 bolts, and remove the chain tensioner assembly No.1.

    3. Remove the timing belt.

  11. DISCONNECT VANE PUMP OIL RESERVOIR ASSEMBLY


    1. A01BBMI

      Remove the 2 bolts. Separate the vane pump oil reservoir assembly.

  12. DISCONNECT OIL RETURN HOSE (w/ Inter Cooler)


    1. A01BFPG

      Loosen the clip.

    2. Disconnect the oil return hose from the intake manifold.

  13. REMOVE EGR PIPE SUB-ASSEMBLY NO.1 (w/ EGR Valve)


    1. A01BDK1

      Remove the bolt, and separate the manifold stay.

    2. Disconnect the vacuum hose from intake air connector.

    3. A01BEP8E01

      Remove the bolt, 2 nuts and the intake air connector assembly.

    4. Remove the 2 gaskets and intake air connector No.2 from the intake air connector.

  14. REMOVE AIR HOSE NO.4


    1. A01BGX6

      Loosen the 2 clamps.

    2. Remove the air hose No.4.

  15. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    1. A01BCMO

      Disconnect the 2 throttle body connectors.

    2. A01BBJH

      Remove the 2 bolts, 2 nuts, and the diesel throttle body assembly.

    3. Remove the gasket from intake air connector.

  16. REMOVE ENGINE SERVICE HOLE COVER NO.2


    1. A01BG4E

      Roll up the carpet.

    2. Remove the 3 bolts and the engine service hole cover No.2.

  17. REMOVE INTAKE AIR CONNECTOR (w/o EGR Valve)


    1. A01BDK1

      Remove the bolt, and separate the manifold stay.

    2. Disconnect the vacuum hose from intake air connector.

    3. A01BEP8E01

      Remove the bolt, 2 nuts and the intake air connector assembly.

    4. Remove the 2 gaskets and intake air connector No.2 from the intake air connector.

  18. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR Valve)


    1. Remove the vacuum regulating valve.


      1. A01BHSL

        Remove the 2 vacuum hoses and the vacuum regulating valve connector.

      2. Remove the 2 bolts and the vacuum regulating valve.

    2. Remove the EGR valve assembly with the sensor.


      1. A01BCF1

        Remove the bolt, and separate the manifold stay.

      2. Disconnect the vacuum hose from the intake air connector.

      3. A01BAPE

        Disconnect the intake air temperature sensor connector.

      4. Disconnect the EGR valve position sensor connector.

      5. A01BACYE01

        Remove the bolt, 2 nuts and the intake air connector assembly.

      6. Remove the 2 gaskets and EGR valve assembly from the intake air connector.

  19. REMOVE OIL LEVEL GAGE GUIDE


    1. Remove the oil level gauge.

    2. Remove the bolt and oil level gauge guide.

  20. REMOVE INJECTION PIPE

    SST
    09023-12701

    1. Remove the injection pipe.


      1. A01BC89

        Remove the 2 nuts and injection pipe clamp No.3.

      2. A01BFG2

        Using SST, remove the 4 injection pipes.

        SST
        09023-12701

  21. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    1. Using SST, remove the fuel inlet pipe sub-assembly.

      SST
      09023-12701

  22. REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY


    1. A01BCD7

      Remove the 4 bolts.

    2. Remove the camshaft timing pulley flange No.2 and pump drive shaft pulley.

    3. A01BFRE

      Using SST, remove the supply pump gear set nut and O-ring while holding the crankshaft pulley.

      SST
      09213-58013
      09330-00021
    4. A01BGD8

      Disconnect the 2 fuel hoses.

    5. Disconnect the 2 connectors and wire harness.

    6. Loosen the 2 nuts as shown in the illustration.

    7. A01BA4CE01

      Using SST, disengage the supply pump from the supply pump gear.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )

    8. Remove the 2 nuts and supply pump from the engine.

    9. Remove the O-ring from the supply pump.

    10. Remove the pulley key from the supply pump.

  23. REMOVE FUEL TEMPERATURE SENSOR


    1. Mount the injection or supply pump assembly in a soft jaw vise.

    2. A01BFXWE01

      Using a SST, remove the fuel temperature sensor.

      SST
      09922-10010

    3. Remove the O-ring form the fuel temperature sensor.