METER / GAUGE SYSTEM CUSTOMIZE PARAMETERS


  1. CUSTOMIZE METER / GAUGE SYSTEM


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Combination Meter / Warning or Display.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Lane Change Flashing Times Setting 3 Function to change the lane change flashing time OFF, 3, 5 or 7 Combination meter assembly
        Flasher Sound Tone Setting Tone 3 Function to change the flasher sound tone Tone 1, Tone 2 or Tone 3 Combination meter assembly

        • *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

        Display
        Display Default Content Setting Relevant ECU
        ECO Drive Indicator Zone ON Function to turn on/off the eco driving indicator zone display ON or OFF Combination meter assembly
        ODO Display Time After IG OFF Setting 30 s Function to change the odometer display time 30 s, 60 s, 600 s or OFF Combination meter assembly

    2. Customizing with the combination meter assembly (for Dot Display Type)


      1. Turn the ignition switch to ON.

      2. Enter the following menus: SETTINGS.

      3. Select the setting by referring to the table below.

        SETTINGS
        Display Default Content Setting Relevant ECU
        LANGUAGE ENGLISH Function to change the multi-information display language ENGLISH or Chinese Combination meter assembly
        UNITS L/100km Function to change the multi-information display unit km/L or L/100km Combination meter assembly
        ECO INDICATOR ON Function to turn on/off the eco driving indicator light ON or OFF Combination meter assembly

    3. Customizing with the combination meter assembly (for Segment Display Type)


      1. Turn the ignition switch to ON.

      2. Display the odometer screen.

      3. Press and hold the ODO/TRIP switch for 5 seconds or more to display the settings screen.

      4. After selecting "Eco On" or "EcoOFF", press and hold the ODO/TRIP switch for 2 seconds or more to exit the settings screen.

    4. Inspect T-BELT mode display (Engine Type Diesel)


      1. Turn the ignition switch to ON.

      2. Turn the ODO/TRIP display screen to "TRIP B", and turn the ignition switch off.

      3. While pressing the ODO/TRIP change switch, turn the ignition switch to ON to blink the T-BELT warning light, and then continue pressing the switch for 5 seconds or more.

      4. Release the ODO/TRIP switch, then press the ODO/TRIP switch again within 5 seconds.

      5. Transfer to the T-BELT mode, and the following initial setting value is displayed.

        km: 15 (0,000 km) or 9 (0,000 mile)

        Tech Tips

        If the meter has been replaced before, the displayed value might not be the same as the initial setting value.

    5. Rewriting replacement setting value (Engine Type Diesel)


      1. Press the ODO/TRIP switch and rewrite the replacement setting value.

        Condition Setting value
        When a belt is replaced

        km: 15 (0,000 km)

        mile: 9 (0,000 mile)
        When a meter is replaced

        km: [15 (0,000 km)] - (Mileage when the meter is replaced)

        mile: [9 (0,000 mile)] - (Mileage when the meter is replaced)

        Tech Tips

        Every press of the ODO/TRIP switch adds 10,000 km or 10,000 mile and the meter returns to 10,000 km or 10,000 mile when 200,000 km or 200,000 mile is reached. If switch operation is not performed within 30 seconds, the setting value will not be changed. The display screen turns to "TRIP B", and the mode returns to the normal mode.

    6. T-BELT mode completion (Engine Type Diesel)

      Note

      If the T-BELT mode is completed, even though belt replacement or meter replacement has not been performed, the T-BELT warning is reset.


      1. After setting the replacement setting value, hold the ODO/TRIP switch on for more than 5 seconds, then release the ODO/TRIP switch.

      2. Check that the display is changed to "TRIP B" and the warning light goes off.