WIPER SWITCH REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO. 1


    1. A01BEMD

      Using a moulding remover D, detach the 3 claws and remove the instrument cluster finish panel garnish No. 1.

  3. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH NO. 2


    1. A01BHUS

      Using a moulding remover D, detach the 3 claws and remove the instrument cluster finish panel garnish No. 2.

  4. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER


    1. for Standard Body:

      Using a moulding remover D, detach the 4 claws in the order shown in the illustration.

    2. for Wide Body:

      Using a moulding remover D, detach the 5 claws in the order shown in the illustration.

      A01BI26E01
      Text in Illustration
      *A for Standard Body *B for Wide Body
    3. A01BAMEE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape as shown in the illustration.

    4. Using a moulding remover D, detach the claw.

    5. A01BAQV

      Detach the claw as shown in the illustration.

    6. A01BEFS

      Detach the 3 claws as shown in the illustration.

    7. A01BEKP

      Detach the 2 claws as shown in the illustration.

    8. for Standard Body:

      Detach the 3 claws and remove the instrument cluster finish panel sub-assembly center.

    9. for Wide Body:

      Detach the 4 claws and remove the instrument cluster finish panel sub-assembly center.

      A01BC7JE01
      Text in Illustration
      *A for Standard Body *B for Wide Body

  5. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01BEAC

      Using a moulding remover D, detach the 4 claws and remove the instrument cluster finish panel assembly.

  6. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01BD2D

      Detach the 6 claws and 4 hooks and remove the instrument cluster finish panel sub-assembly.

  7. REMOVE COMBINATION METER ASSEMBLY


    1. A01BAIH

      Remove the 2 screws.

    2. A01BFCK

      Detach the 2 claws and remove the combination meter assembly.

    3. Disconnect the 2 connectors and detach the wire harness clamp.

  8. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER


    1. A01BD8D

      Using a clip remover, remove the 2 clips.

    2. Detach the 4 clips and remove the instrument panel finish lower.

    3. Disconnect each connector.

    4. A01BHHW

      Push the positions indicated by the arrows in the illustration to disconnect the fuel lid lock control cable and bonnet (hood) control cable assembly from the instrument panel finish lower.

  9. REMOVE NO. 2 STEERING COLUMN LOWER COVER (w/ Smart Entry and Start System)


    1. A01BGLA

      Detach the 4 claws and remove the No. 2 steering column lower cover.

  10. REMOVE STEERING COLUMN LOWER COVER

    Tech Tips

    Adjust the position of the steering tilt mechanism when performing the procedure.


    1. A01BGHW

      While turning the steering wheel to the right.

    2. Using a T25 ''TORX'' socket wrench, remove the ''TORX'' screw.

    3. A01BGYC

      While turning the steering wheel to the left.

    4. Using a T25 ''TORX'' socket wrench, remove the ''TORX'' screw.

    5. A01BGF5

      Push the steering column lower cover inward on both sides to detach the 2 claws.

    6. A01BGCL

      Detach the 2 claws and remove the steering column lower cover.

  11. REMOVE STEERING COLUMN UPPER COVER


    1. A01BGF6E01
      Text in Illustration
      *a Front of Vehicle
      *b Raise the backside of the steering column upper cover
      *c Pull diagonally backwards so that the claw of the steering column upper cover does not break

      Remove the steering column upper cover from the steering column assembly.

      Note

      If the steering column upper cover is removed by pulling it directly upwards, the claw may become damaged.

  12. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY


    1. Disconnect the 2 connectors.

    2. A01BG40

      Detach the claw and remove the windshield wiper switch assembly as shown in the illustration.

      Note

      If the claw is pushed with excessive force, it may be broken.