INSTRUMENT PANEL SAFETY PAD INSTALLATION


  1. INSTALL INSTRUMENT PANEL ASSEMBLY


    1. Connect the all connectors.

    2. Install the instrument panel assembly with the 4 bolts <A>, 2 screws <B> and 2 nuts <D>.

      A01BEMAE01

  2. INSTALL FRONT PILLAR GARNISH RH

  3. INSTALL FRONT PILLAR GARNISH LH

  4. INSTALL ASSIST GRIP ASSEMBLY

  5. INSTALL FRONT ASSIST GRIP NO.1 PLUG

  6. INSTALL HAZARD WARNING SIGNAL SWITCH ASSEMBLY

  7. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)


    1. A01BDV8

      With the front passenger airbag installed on the vehicle, perform a visual check. If there are any defects mentioned below, replace the instrument panel with a new one:


      • Cuts, minute cracks or marked discoloration on the instrument panel around the front passenger airbag.

  8. INSTALL AIR CONDITIONER PANEL SUB-ASSEMBLY


    1. A01BFRJ

      Install the heater control base with the 2 screws.

    2. A01BGTGE01

      Engage the 2 claws to install the defroster damper control cable sub-assembly.

    3. A01BE9DE01

      Engage the 2 claws to install the boost ventilator control cable sub-assembly.

    4. Install the clamp.

    5. Install the connector.

    6. A01BF7ZE01

      Engage the 9 clips to install the air conditioner panel sub-assembly.

  9. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY (for Automatic Transmission)

    For 2KD-FTV Click here

    For 2TR-FE Click here

  10. INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY (for Manual Transmission)

    For 5L-E Click here

    For 2KD-FTV, 2TR-FE Click here

  11. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

  12. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER


    1. A01BB5ME01

      Engage the 8 claws and install the instrument panel finish panel lower center.

  13. INSTALL SHIFTING HOLE COVER ASSEMBLY


    1. A01BF5BE01

      Manual Transmission:

      Engage the 6 claws and install the shifting hole cover assembly.

    2. Automatic Transmission:

      Engage the 8 claws and install the sifting hole cover assembly.

  14. INSTALL SHIFT LEVER KNOB

  15. INSTALL PARKING BRAKE HOLE COVER


    1. A01BF1ME01

      Engage the 6 claws and install the parking brake hole cover.

  16. INSTALL INSTRUMENT PANEL NO.1 UNDER COVER SUB-ASSEMBLY


    1. A01BE86E01

      Engage the 3 claws.

    2. Install the instrument panel No.1 under cover sub-assembly with the 2 clips.

  17. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER


    1. A01BHMVE01

      Engage the 4 clips (B).

    2. Install the instrument panel finish panel lower with the 2 clips (A).

  18. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

  19. INSTALL STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01BAJI

      Install the radio tuner opening cover with bracket with the 4 screws <C>.

  20. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    1. A01BFVC

      Install the instrument panel cup holder assembly with the 3 screws <C>.

  21. INSTALL COMBINATION METER ASSEMBLY


    1. A01BE2WE01

      Connect the connector and engage the 2 claws.

    2. A01BAQR

      Install the combination meter assembly with the 2 screws <B>.

  22. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Engage the 6 claws and install the instrument cluster finish panel sub-assembly.

  23. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  24. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 GARNISH

  25. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER

  26. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.2 GARNISH

  27. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY


    1. Install the wiper switch with the claw.

      Tech Tips

      Slide the steering column cover upper upward to install the wiper switch.

    2. Connect the connector.

  28. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY


    1. Install the headlight dimmer switch with the claw.

      Tech Tips

      Slide the steering column upper cover upward to install the headlight dimmer switch.

    2. Connect the connector.

  29. INSTALL STEERING COLUMN COVER UPPER

  30. INSTALL KEY CYLINDER LIGHT ASSEMBLY (w/ Key Cylinder Light)

  31. INSTALL STEERING COLUMN COVER LOWER


    1. A01BEIN

      Engage the 3 claws to install the steering column cover upper and lower with the 2 "torx" screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  32. ADJUST SPIRAL CABLE SUB-ASSEMBLY (w/ SRS Airbag)


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) terminal is disconnected.

      CAUTION:

      After removing the terminal, wait for at least 90 seconds before starting the operation.

    3. A01BDHD

      Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

      Note

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

    4. A01BD2G

      Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

      Tech Tips

      The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.

  33. INSTALL STEERING WHEEL ASSEMBLY


    1. A01BEFRE01

      w/o AIRBAG:


      1. Position the horn contact plate so that the projecting parts are as shown the illustration.

    2. Align the matchmarks on the steering wheel assembly and the steering column assembly.

    3. Install the nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    4. Connect the connectors.

  34. INSTALL STEERING PAD (w/o SRS Airbag)


    1. Connect the horn connector.

    2. A01BAW6E01

      Install the steering pad with the screw.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  35. INSTALL STEERING PAD (w/ SRS Airbag)


    1. A01BH9D

      With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:


      • Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system.

  36. INSTALL STEERING WHEEL NO.3 COVER LOWER

  37. INSTALL STEERING WHEEL NO.2 COVER LOWER

  38. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  39. INSPECT STEERING PAD (w/ SRS Airbag)


    1. Perform a diagnostic system check. Click here

    2. A01BH9D

      With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:


      • Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  40. INSPECT SRS WARNING LIGHT (w/ SRS Airbag)

    Click here