OUTER MIRROR SWITCH INSPECTION


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)


    1. Check the mirror select switch and mirror surface adjust switch.


      1. A01BAUWE01
        Text in Illustration
        *1 Mirror Select Switch
        *2 Mirror Surface Adjust Switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        9 (VL) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        9 (VL) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        10 (HL) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        10 (HL) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        8 (VR) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        8 (VR) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        7 (HR) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        7 (HR) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check that the LED illuminates.


      1. A01BCURE01
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) - 6 (ILL+)

        Battery negative (-) - 16 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)


    1. Check the mirror select switch and mirror surface adjust switch.


      1. A01BDU9E17
        Text in Illustration
        *1 Mirror Select Switch
        *2 Mirror Surface Adjust Switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        9 (VL) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        9 (VL) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        10 (HL) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        10 (HL) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        8 (VR) - 13 (B)

        11 (M+) - 12 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        8 (VR) - 12 (E)

        11 (M+) - 13 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        7 (HR) - 13 (B)

        11 (M+) - 12 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        7 (HR) - 12 (E)

        11 (M+) - 13 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the retract switch.


      1. A01BDU9E18
        Text in Illustration
        *1 Retract Switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition

        13 (B) - 15 (MF)

        12 (E) - 14 (MR)

        		 Pushed in Below 1 Ω

        12 (E) - 15 (MF)

        13 (B) - 14 (MR)

        		 Not pushed in Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    3. Check that the LED illuminates.


      1. A01BFPBE01
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) - 6 (ILL+)

        Battery negative (-) - 16 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.