SFI SYSTEM, Diagnostic DTC:P0010

DESCRIPTION

• This DTC is designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

• The VVT (variable valve timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

MONITOR DESCRIPTION

The ECM optimizes the valve timing using the VVT system to control the intake camshaft. The VVT system includes the ECM, the OCV and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

After the ECM sends the target duty-cycle signal to the OCV, the ECM monitors the OCV current to establish an actual duty-cycle. The ECM determines the existence of a malfunction and sets the DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.

CONFIRMATION DRIVING PATTERN

1. Connect the intelligent tester to the DLC3.

2. Turn the ignition switch to ON and turn the intelligent tester on.

3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4. Turn the ignition switch off and wait for at least 30 seconds.

5. Turn the ignition switch to ON and turn the intelligent tester on.

6. Wait 5 seconds or more.

7. Enter the following menus: Powertrain / Engine and ECT / DTC.

8. Read the pending DTCs.

   Tech Tips

   
   

   • If a pending DTC is output, the system is malfunctioning.

   • If a pending DTC is not output, perform the following procedure.

9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10. Input the DTC: P0010.

11. Check the DTC judgment result.

    Intelligent tester Display	Description
    NORMAL	DTC judgment completed System normal
    ABNORMAL	DTC judgment completed System abnormal
    INCOMPLETE	DTC judgment completed Perform driving pattern after confirming DTC enabling conditions
    N/A	Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips

    
    

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK FOR DTC

   
   

   1. Clear the DTCs after recording the freeze frame data and DTCs Click here.

   2. Turn the ignition switch off.

   3. Start the engine and allow it to idle. Then check for DTCs.

   4. Check that P0010 is not output.

      OK
      P0010 is not output.

   
   

   NG

   INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY Click here

   OK

   CHECK FOR INTERMITTENT PROBLEMS Click here

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

   
   

   1. Inspect the camshaft timing oil control valve assembly Click here.

   
   

   NG

   REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY Click here

   OK

3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

   
   

   1. Disconnect the camshaft timing oil control valve connector.

   2. Disconnect the ECM connector.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition D78-2 - D1-13 (OC1+) Always Below 1 Ω D78-1 - D1-12 (OC1-) Always Below 1 Ω D78-2 or D1-13 (OC1+) - Body ground Always 10 kΩ or higher D78-1 or D1-12 (OC1-) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

   REPLACE ECM Click here