ECD SYSTEM (w/ DPF), Diagnostic DTC:P062F

DTC Code DTC Name
P062F Internal Control Module EEPROM Error

DESCRIPTION

P062F
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second

When any condition below is met (1 trip detection logic):


  • Fuel injector compensation code is not registered.

  • Wrong injector compensation code is registered.

  • Fuel injector pilot quantity learning value is not registered.

  • Catalyst deterioration learning value is not registered.

  • Crank Time Compensation Learning value is not registered.*

  • A/F Sensor Compensation Learning value is not registered.*

  • Fuel injector compensation code

  • Fuel injector pilot quantity learning value

  • Catalyst thermal deterioration value

  • A/F sensor compensation learning value

  • Crank time compensation learning value

  • ECM

*: When this malfunction occurs, the MIL does not illuminate.

Note


  • When a injector assembly is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.

  • Fuel injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect fuel injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

  • When a injector assembly is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing fuel injector pilot quantity learning values must be input into the new ECM.

  • When the catalyst converter is replaced, the new catalyst thermal deterioration value must be input into the ECM. When the ECM is replaced, the existing catalyst thermal deterioration value must be input into the new ECM.

Tech Tips

When replacing the ECM with a new one, if the injector compensation code, injector pilot quantity learning value and/or catalyst thermal deterioration value are not entered, DTC P062F will be stored.


  1. When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:


    1. Prior to replacing the ECM, use the GTS to read and save each learning value and code from the original ECM Click here.

    2. After installing a new ECM, input the saved learning values and codes into the new ECM using the GTS Click here.

    3. Turn the ignition switch off and turn the GTS off.

    4. Wait for at least 30 seconds.

    5. Turn the ignition switch to ON and turn the GTS on.

    6. Clear DTC P062F stored in the ECM using the GTS Click here.

      Tech Tips


      • Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

      • When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.

        Replacement Part Utility Item
        ECM
        DPF catalyst
        Injector

INSPECTION PROCEDURE

Note


  • After replacing the ECM, the new ECM needs registration Click here and initialization Click here.

  • After replacing the fuel supply pump assembly, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. LEARNING VALUES CONFIRMATION


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation Click here.

      Result
      Result Proceed to
      The injector compensation codes are not input A
      The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors A
      The pilot quantity learning values are set to the default values B
      The catalyst deterioration learning values are set to the default values B
      Except above C

      Tech Tips


      • When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

      • When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.


    B

    LEARNING VALUES WRITE Click here

    C

    CHECK DTC OUTPUT Click here

    A

  2. REGISTER INJECTOR COMPENSATION CODE


    1. Register the injector compensation code Click here.


    NEXT

    PILOT QUANTITY LEARNING Click here

  3. LEARNING VALUES WRITE

    Tech Tips

    When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the GTS and replacing the old ECM with a new one, "Learning Values Write" was not performed using the GTS causing this DTC to be output.


    1. Install the old ECM.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save Click here.

    5. Remove the old ECM.

    6. Install a new ECM.

    7. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write Click here.


    NEXT

  4. LEARNING VALUES CONFIRMATION


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation Click here.

      Result
      Result Proceed to
      The pilot quantity learning values are set to the default values A
      The catalyst deterioration learning values are set to the default values B
      Except above C

      Tech Tips


      • When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.

      • When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.


    B

    REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYST CONVERTER) Click here

    C

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    A

  5. PILOT QUANTITY LEARNING


    1. Perform the fuel injector pilot quantity learning Click here.


    NEXT

    CHECK DTC OUTPUT Click here

  6. REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYST CONVERTER)


    1. Replace the front exhaust pipe assembly Click here.


    NEXT

  7. CATALYST RECORD CLEAR


    1. Perform the catalyst record clear Click here.


    NEXT

  8. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    4. Turn the ignition switch to ON for 1 second.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Read the DTCs.

      Result
      Result Proceed to
      No DTC is output A
      P062F is output B

    B

    REPLACE ECM Click here

    A

    END

  9. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  10. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    4. Turn the ignition switch to ON for 1 second.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Confirm that the DTC is not output again.


    NEXT

    END