REPAIR INSTRUCTION CUSTOMIZE PARAMETERS


  1. CUSTOMIZE SMART ENTRY AND START SYSTEM (for 1KD FTV, Start Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize / Entry&Start.

      5. Select the setting by referring to the table below.

        Entry&Start
        Display Default Content Setting Relevant ECU
        Auto Entry Cancel SW OFF Function that enables or disables the smart entry and start system. OFF or ON Certification ECU (smart key ECU assembly)

    2. Entry cancel function (manual operation)

      Tech Tips

      While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


      1. The following functions are disabled when the smart entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Push-button start function

        3. Key lock-in prevention function

        4. Entry warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The engine switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock switch of the electrical key transmitter sub-assembly.

        3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

        4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

        5. Perform the following procedure within 30 seconds of completing the step above.


          1. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).

          2. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times.

            Note

            If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

          3. Close and open the driver door (driver door: open → closed → opened).

        6. Close the driver door within 5 seconds (driver door: open → closed).

        7. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

      3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the smart entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  2. CUSTOMIZE SEAT BELT WARNING SYSTEM

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Utility / Customize Setting / Warning.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer*1 ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer*2 ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly

        • *1: w/ Driver Side Seat Belt Warning Buzzer

        • *2: w/ Front Passenger Seat Belt Warning System

        Tech Tips

        This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

  3. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Entry&Start / Utility / Customize / Door Lock.

        Entry&Start
        Display Default Content Setting Relevant ECU
        Wireless Buzzer Volume Setting Level5 Function that changes the wireless buzzer volume. OFF, Level7(MAX), Level6, Level5, Level 4, Level3, Level2, Level1, Level0(Mute) Certification ECU (smart key ECU assembly)

  4. CUSTOMIZE SMART ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Entry&Start.

      5. Select the setting by referring to the table below.

        Entry&Start
        Display Default Content Setting Relevant ECU
        Door Unlock Mode2 All Function that chooses the doors to be operated by entry unlock operation. All, Driver Certification ECU (smart key ECU assembly)
        Auto Entry Cancel SW OFF Function that enables or disables the smart entry and start system. OFF, ON Certification ECU (smart key ECU assembly)
        Wireless Buzzer Volume Setting Level5 Wireless buzzer answer back volume. OFF, Level7(MAX), Level6, Level5, Level4, Level3, Level2, Level1, Level0(Mute) Certification ECU (smart key ECU assembly)

    2. Entry cancel function (manual operation)

      Tech Tips

      While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.


      1. The following functions are disabled when the smart entry and start system is canceled.


        1. Entry unlock/lock functions

        2. Push start function

        3. Key lock-in prevention function

        4. Entry warning functions

      2. When canceling the system through manual operation:


        1. Make sure the following conditions are met:


          • The engine switch is off.

          • The driver door is closed.

          • The driver door is unlocked.

        2. Press the unlock button of the electrical key transmitter sub-assembly.

        3. Open the driver door within 5 seconds of completing the step above (driver door: close condition → opened).

        4. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

        5. Close and open the driver door twice completing the above step (driver door: open condition → closed → opened → closed → opened).

        6. With the driver door open, press the unlock button of the electrical key transmitter sub-assembly 2 times completing the step above.

          Note

          If the driver door is closed before or while pressing the unlock button, the entry cancel setting mode will end.

        7. Close and open the driver door completing the step above (driver door: open condition → closed → opened).

        8. Close the driver door within 5 seconds of completing the above step.

        9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the smart entry and start system has been canceled.

          Tech Tips

          Finish the step 5 to 7 within 30 seconds.

      3. Perform the following procedure to restore the smart entry and start system to the active state from the canceled state.


        1. Perform the procedures to cancel the smart entry and start system again.

        2. Check that the wireless buzzer sounds once (short beep) to confirm that the smart entry and start system has been restored to the active state.

          Tech Tips


          • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

          • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.

  5. CUSTOMIZE LIGHTING SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Utility / Customize / Warning.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Lane Change Flashing Times Setting 3 Function to change the number of flashes for the lane change flasher OFF, 3, 5 or 7 Combination meter assembly
        Flasher Sound Tone Setting Tone 3 Function to change the flasher sound. Tone 1, Tone 2 or Tone 3 Combination meter assembly

  6. CUSTOMIZE METER / GAUGE SYSTEM


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Combination Meter / Warning or Display.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Lane Change Flashing Times Setting 3 Function to change the lane change flashing time OFF, 3, 5 or 7 Combination meter assembly
        Flasher Sound Tone Setting Tone 3 Function to change the flasher sound tone Tone 1, Tone 2 or Tone 3 Combination meter assembly

        • *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

        Display
        Display Default Content Setting Relevant ECU
        ECO Drive Indicator Zone ON Function to turn on/off the eco driving indicator zone display ON or OFF Combination meter assembly
        ODO Display Time After IG OFF Setting 30 s Function to change the odometer display time 30 s, 60 s, 600 s or OFF Combination meter assembly

    2. Customizing with the combination meter assembly (for Dot Display Type)


      1. Turn the ignition switch to ON.

      2. Enter the following menus: SETTINGS.

      3. Select the setting by referring to the table below.

        SETTINGS
        Display Default Content Setting Relevant ECU
        LANGUAGE ENGLISH Function to change the multi-information display language ENGLISH or Chinese Combination meter assembly
        UNITS L/100km Function to change the multi-information display unit km/L or L/100km Combination meter assembly
        ECO INDICATOR ON Function to turn on/off the eco driving indicator light ON or OFF Combination meter assembly

    3. Customizing with the combination meter assembly (for Segment Display Type)


      1. Turn the ignition switch to ON.

      2. Display the odometer screen.

      3. Press and hold the ODO/TRIP switch for 5 seconds or more to display the settings screen.

      4. After selecting "Eco On" or "EcoOFF", press and hold the ODO/TRIP switch for 2 seconds or more to exit the settings screen.

    4. Inspect T-BELT mode display (Engine Type Diesel)


      1. Turn the ignition switch to ON.

      2. Turn the ODO/TRIP display screen to "TRIP B", and turn the ignition switch off.

      3. While pressing the ODO/TRIP change switch, turn the ignition switch to ON to blink the T-BELT warning light, and then continue pressing the switch for 5 seconds or more.

      4. Release the ODO/TRIP switch, then press the ODO/TRIP switch again within 5 seconds.

      5. Transfer to the T-BELT mode, and the following initial setting value is displayed.

        km: 15 (0,000 km) or 9 (0,000 mile)

        Tech Tips

        If the meter has been replaced before, the displayed value might not be the same as the initial setting value.

    5. Rewriting replacement setting value (Engine Type Diesel)


      1. Press the ODO/TRIP switch and rewrite the replacement setting value.

        Condition Setting value
        When a belt is replaced

        km: 15 (0,000 km)

        mile: 9 (0,000 mile)
        When a meter is replaced

        km: [15 (0,000 km)] - (Mileage when the meter is replaced)

        mile: [9 (0,000 mile)] - (Mileage when the meter is replaced)

        Tech Tips

        Every press of the ODO/TRIP switch adds 10,000 km or 10,000 mile and the meter returns to 10,000 km or 10,000 mile when 200,000 km or 200,000 mile is reached. If switch operation is not performed within 30 seconds, the setting value will not be changed. The display screen turns to "TRIP B", and the mode returns to the normal mode.

    6. T-BELT mode completion (Engine Type Diesel)

      Note

      If the T-BELT mode is completed, even though belt replacement or meter replacement has not been performed, the T-BELT warning is reset.


      1. After setting the replacement setting value, hold the ODO/TRIP switch on for more than 5 seconds, then release the ODO/TRIP switch.

      2. Check that the display is changed to "TRIP B" and the warning light goes off.