ENGINE COOLANT TEMPERATURE SENSOR REMOVAL


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  3. REMOVE ENGINE UNDER COVER NO.1 (w/ Engine Under Cover No.1)

  4. REMOVE ENGINE UNDER COVER NO.2 (w/ Engine Under Cover No.2)


    1. Remove the engine under cover No.2 together with the engine side under cover LH and engine side under cover RH (for Wide Body).

  5. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Remove the radiator cap.

    2. Loosen the radiator drain plug and a cylinder block drain plug. Then drain the coolant.

      A01BFQWE01

  6. REMOVE FRONT SEAT ASSEMBLY RH (for Hi-back Seat Type)

    Tech Tips

    Use the same procedures described for the LH side. Click here

  7. REMOVE FRONT SEAT ASSEMBLY RH (for Low-back Seat Type)

    Tech Tips

    Use the same procedures described for the LH side. Click here

  8. REMOVE FRONT DOOR SCUFF PLATE RH

  9. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY


    1. Roll up the carpet, and remove the 5 bolts and engine service hole sub cover.

  10. REMOVE INTAKE AIR CONNECTOR


    1. A01BGFJE01

      Slide the clamp and disconnect the No. 2 ventilation hose and vacuum hose. (A)

    2. Loosen the 2 hose clamp bolts. (B)

    3. Remove the 2 bolts and intake air connector. (C)

  11. REMOVE THROTTLE BODY ASSEMBLY


    1. A01BD19E01

      Disconnect the throttle motor connector. (A)

    2. Slide the clamp and disconnect the water by-pass hose. (B)

    3. Slide the clamp and disconnect the No. 2 water by-pass hose. (C)

    4. for Type A:

      Remove the 2 bolts and 2 nuts, and then remove the throttle body assembly. (D)

    5. for Type B:

      Remove the 4 bolts and throttle body assembly. (D)

    6. A01BA4J

      Remove the gasket from the intake manifold.

  12. DISCONNECT FUEL HOSE


    1. A01BI68E01

      Pull the fuel hose connector cover up to release the lock. Click here

    2. Disengage the fuel connector to disconnect the fuel hose. Click here

  13. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

    Note

    Be careful not to drop the injectors when removing the delivery pipe.


    1. A01BI1P

      Disconnect the fuel hoses.

    2. Disconnect the 4 injector connectors.

    3. Remove the 2 bolts O-ring and fuel pulsation damper assembly.

    4. Remove the 2 bolts and delivery pipe together with the 4 injectors.

    5. Remove the delivery pipe spacers.

    6. A01BEYP

      Using a screwdriver, pry out the 4 spacers from the cylinder head.

  14. REMOVE FUEL INJECTOR ASSEMBLY


    1. A01BDW5E01

      Pull out the 4 injectors from the delivery pipe.

    2. Remove the O-rings from the injectors.

  15. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY (for Automatic Transmission)


    1. A01BCTHE01

      Remove the 2 bolts transmission oil filler tube sub-assembly.

    2. Remove the O-ring from the oil filler tube sub-assembly.

  16. REMOVE INTAKE MANIFOLD


    1. Disconnect the vacuum hose and connector from the VSV.

    2. A01BGFG

      Disconnect the 2 wire harness clamps.

    3. Disconnect the ventilation hose No.3 from the intake manifold.

    4. Loosen the 2 clips and disconnect the brake booster hose and the fuel vapor feed hose from the intake manifold.

    5. A01BI3V

      Remove the bolt and the wire harness bracket from the intake manifold.

    6. A01BETV

      Remove the 5 bolts, 2 nuts, and intake manifold.

    7. Remove the gasket from the intake manifold.

  17. REMOVE E.F.I. ENGINE COOLANT TEMPERATURE SENSOR


    1. Disconnect the engine coolant temperature sensor connector.

    2. A01BED7

      Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.