AIRBAG SYSTEM SRS Warning Light does not Come ON

DESCRIPTION

The SRS warning light is located in the combination meter assembly. When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically. If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver. When Terminals TC and CG of the DLC3 are connected, the DTCs are indicated through SRS warning light blinking patterns.

WIRING DIAGRAM

Refer to "DTC B1662/45 Indicator Light Circuit Malfunction" Click here.

INSPECTION PROCEDURE

Tech Tips


  • Once the cause of the trouble has been eliminated, clear the DTCs which were stored during troubleshooting and then check for DTCs to confirm whether the system is sound Click here.

PROCEDURE


  1. CHECK BATTERY VOLTAGE


    1. Measure the voltage of the battery.

      Standard Voltage
      11 to 14 V

    NG

    CHECK CHARGING SYSTEM AND BATTERY Click here

    OK

  2. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that Connectors C13 and C14 are properly connected to the combination meter assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      After confirming that the connectors are secured in the correct positions, proceed to the next check.

    4. Disconnect the connectors from the combination meter assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not damaged.

    NG

    REPLACE WIRE HARNESSES AND COMPONENTS WITH DAMAGED CONNECTORS

    OK

  3. CHECK COMBINATION METER ASSEMBLY (POWER SOURCE)

    A01KG7XE02
    Text in Illustration
    *a

    Rear view of wire harness connector

    (to Combination Meter Assembly)

    1. Confirm that Connectors C13 and C14 are disconnected.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C13-28 - C13-25 Ignition switch ON 8 to 16 V
      C13-28 - C14-6 Ignition switch ON 8 to 16 V

    5. Turn the ignition switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C13-25 - Body ground Always Below 1 Ω
      C14-6 - Body ground Always Below 1 Ω

    NG

    REPLACE COWL WIRE

    OK

  4. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that Connector A23 is properly connected to the airbag ECU assembly.

      OK
      The connector is properly connected and secured.

      Tech Tips

      After confirming that the connector is secured in the correct position, proceed to the next check.

    4. Disconnect the connector from the airbag ECU assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not damaged.

    NG

    REPLACE WIRE HARNESSES AND COMPONENTS WITH DAMAGED CONNECTORS

    OK

  5. CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

    A01KG23E02
    Text in Illustration
    *a

    Rear view of wire harness connector

    (to Airbag ECU Assembly)
    *b

    Rear view of wire harness connector

    (to Combination Meter Assembly)

    1. Confirm that Connector A23 is disconnected.

    2. Confirm that Connector C14 is disconnected.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A23-11 (LA) - C14-19 Always Below 1 Ω
      A23-11 (LA) - Body ground Always 1 MΩ or higher

    NG

    REPLACE COWL WIRE

    OK

  6. CHECK SRS WARNING LIGHT OPERATION


    1. Connect Connector C13.

    2. Connect Connector C14.

    3. Confirm that Connector A23 is disconnected.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the ignition switch to ON.

    6. Check that the SRS warning light comes on after the ignition switch is turned to ON.

      OK
      The SRS warning light comes on and remains on.

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

    REPLACE AIRBAG ECU ASSEMBLY Click here