REAR AXLE HUB BOLT (for Just Low Double Tire) REPLACEMENT

Tech Tips

Replace the RH side by the same procedures with the LH side.


  1. REMOVE REAR AXLE SHAFT LH

  2. REMOVE REAR AXLE SHAFT GASKET LH

  3. REMOVE REAR TIRE

  4. REMOVE REAR AXLE BEARING LOCK NUT

    A01KG9EE01

    1. Remove the 2 screws from the rear axle bearing lock nut.

    2. Using SST, remove the rear axle bearing lock nut.

      SST
      09509-25011

    3. Remove the rear axle lock nut plate LH.

    4. Remove the outer bearing tapered roller bearing.

  5. REMOVE AXLE HUB W/DRUM

  6. REMOVE REAR AXLE LH HUB BOLT


    1. A01KFZ7

      Unstake the 6 bolts and remove the 6 nuts.

    2. A01KIC1

      Using a press, remove the rear axle hub bolt LH.

  7. INSTALL REAR AXLE LH HUB BOLT


    1. A01KF37

      Using a press, install the rear axle hub bolt LH.

    2. Install the 6 nuts then stake the hub bolt LH.

      Torque:
      123 N*m  { 1254 kgf*cm, 91 ft.*lbf }

  8. INSTALL AXLE HUB W/DRUM

  9. INSTALL REAR AXLE BEARING LOCK NUT


    1. Install the rear axle bearing lock nut plate LH.

    2. Install the lock nut.

  10. ADJUST PRELOAD


    1. A01KGTDE01

      Using SST, torque the lock nut.

      SST
      09509-25011
      Torque:
      58 N*m  { 600 kgf*cm, 43 ft.*lbf }

    2. Snug down the bearing by turning the hub several times.

    3. Using SST, retorque the lock nut.

      Torque:
      58 N*m  { 600 kgf*cm, 43 ft.*lbf }
      SST
      09509-25011

    4. Using SST, loosen the lock nut by until it can turned hand.

      SST
      09509-25011
    5. A01KGTJE01
      Text in Illustration
      *a 90°

      Using a spring tension gauge, measure the preload at the hub bolt.

      Preload (at starting)
      5 to 34 N (0.5 to 3.5 kgf, 1.19 to 7.7 lbf)

      Tech Tips

      Within the specified preload, align a lock nut mark with an axle housing mark.

      If preload is not within the specification, repeat the procedure above.

    6. A01KEYNE01
      Text in Illustration
      *1 Axle Housing
      *2 Lock Nut Plate
      *3 Bearing Lock Nut
      *a Correct
      *b Incorrect
      *c -0.2 to 0.9 mm
      *d 2 to 3 mm

      Measure the distance between the top surface of axle housing and the lock nut.

      Standard distance
      -0.2 to 0.9 mm (-0.008 to 0.035 in.)

      If not within the specification, reinstall the axle hub.

  11. INSPECT AXLE HUB AXIAL PLAY


    1. A01KGCX

      Using a dial indicator, check the axle hub axial play.

      Standard clearance
      0.1 mm (0.0039 in.) or less

  12. INSTALL REAR TIRE

    Torque:
    170 N*m  { 1734 kgf*cm, 125 ft.*lbf }

  13. INSTALL REAR AXLE SHAFT GASKET LH

  14. INSTALL REAR AXLE SHAFT LH

    Click here