OIL AND OIL FILTER REPLACEMENT

Note


  • Prolonged and repeated contact with engine oil will cause the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants that may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.


  1. REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)

    A01KF1Z

    1. Remove the 3 screws and rear door scuff plate.

  2. REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

    A01KINS

    1. Remove the 3 screws and rear door scuff plate.

  3. REMOVE REAR FLOOR MAT (for Double Cab)

  4. REMOVE NO. 4 MAT SET PLATE (for Double Cab)

    A01KGPT

    1. Remove the 8 screws and mat set plate.

  5. REMOVE TRANSMISSION SERVICE HOLE COVER SUB-ASSEMBLY (for Double Cab)

    A01KGIJ

    1. Remove the 3 bolts and transmission service cover.

  6. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the drain plug from the oil pan and drain the engine oil into a container.

    3. Clean the drain plug.

    4. Install the drain plug with a new gasket.

      Torque:
      34 N*m  { 347 kgf*cm, 25 ft.*lbf }

  7. REMOVE OIL FILTER


    1. Using SST, remove the oil filter.

      SST
      09228-07501

      Tech Tips

      Because the oil in the filter flows out through the vinyl tube, place the drain oil container under the vinyl tube.

  8. INSTALL OIL FILTER


    1. Clean the oil filter installation surface.

    2. Apply engine oil to the oil filter gasket.

    3. Lightly screw a new oil filter to the oil cooler cover until the oil filter does not turn.

    4. Using SST, tighten the oil filter an additional 3/4 turn.

      SST
      09228-07501
      Torque:
      17 N*m  { 173 kgf*cm, 13 ft.*lbf }

  9. ADD ENGINE OIL


    1. Add fresh oil and install the oil filler cap.

      Engine oil
      Item Oil Grade Oil Viscosity (SAE)
      w/ DPF

      • ACEA C2

      (Using engine oil other than ACEA C2 may damage catalytic converter)

      • 0W-30

      • 5W-30
      w/o DPF

      • G-DLD1, API CF-4, CF or ACEA B1

      • 5W-30


      • 10W-30


      • 15W-40


      • 20W-50
      Capacity
      Item Fill Amount
      Drain and refill with oil filter change 7.0 liters (7.4 US qts, 6.2 Imp. qts)
      Drain and refill without oil filter change 6.8 liters (7.2 US qts, 6.0 Imp. qts)
      Dry fill 7.7 liters (8.1 US qts, 6.8 Imp. qts)

  10. INSPECT FOR OIL LEAK


    1. Warm up the engine and inspect for oil leak.

  11. INSPECT ENGINE OIL LEVEL


    1. Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.

      If low, check for leakage and add oil up to the full level mark.

      Note

      Do not fill engine oil above the full level mark.

  12. INSTALL TRANSMISSION SERVICE HOLE COVER SUB-ASSEMBLY (for Double Cab)


    1. Install the transmission service cover with the 3 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  13. INSTALL NO. 4 MAT SET PLATE (for Double Cab)


    1. Install the mat set plate with the 8 screws.

  14. INSTALL REAR FLOOR MAT (for Double Cab)

  15. INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)


    1. Install the rear door scuff plate with the 3 screws.

  16. INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab)


    1. Install the rear door scuff plate with the 3 screws.