EGR VALVE (w/o DPF) REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

  2. DRAIN ENGINE COOLANT

    CAUTION:

    To avoid the danger of being burned, do not remove the radiator cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.


    1. A01KFNQE02
      Text in Illustration
      *1 Radiator Cap
      *2 Engine Drain Plug
      *3 Radiator Drain Plug

      Loosen the radiator drain plug (on the radiator).

    2. Remove the radiator cap.

    3. Loosen the engine drain plug (on the oil cooler cover), and drain the coolant.

    4. Drain the coolant from the reservoir tank.

    5. Tighten the engine drain plug.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. REMOVE FRONT SEAT ASSEMBLY LH (for Double Cab)


    1. Disconnect the connector.

    2. Remove the 4 bolts and front seat LH.

  4. REMOVE FRONT DOOR SCUFF PLATE LH (for Double Cab)

    A01KG08

    1. Remove the 4 screws and front door scuff plate LH.

  5. REMOVE PARKING BRAKE HOLE COVER (for Double Cab)

    A01KHZT

    1. Remove the screw and parking brake hole cover.

  6. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Double Cab)

  7. REMOVE FRONT FLOOR PANEL BRACE (for Double Cab)

    A01KFZF

    1. Remove the 3 clips, then remove the floor panel brace with the shifting hole cover.

  8. REMOVE NO. 1 FRONT FLOOR MAT REAR (for Double Cab)

  9. SEPARATE FLOOR SHIFT CABLE TRANSMISSION CONTROL SELECT (for Double Cab)


    1. A01KF9M

      Remove the clip.

    2. Remove the clip and washer, and separate the floor shift cable transmission control select.

  10. SEPARATE FLOOR SHIFT CABLE TRANSMISSION CONTROL SHIFT (for Double Cab)


    1. A01KECI

      Remove the clip.

    2. Remove the nut and washer, and separate the floor shift cable transmission control shift.

  11. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY (for Double Cab)

    A01KGMH

    1. Remove the 4 bolts and transmission floor shift.

  12. SEPARATE PARKING BRAKE LEVER ASSEMBLY (for Double Cab)

    A01KH1U

    1. Disconnect the connector.

    2. Remove the 4 bolts, and separate the parking brake lever with parking brake cable.

  13. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY (for Double Cab)

    A01KEH0

    1. Remove the 7 bolts and engine service hole sub cover.

  14. REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)

    A01KF1Z

    1. Remove the 3 screws and rear door scuff plate.

  15. REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

    A01KINS

    1. Remove the 3 screws and rear door scuff plate.

  16. REMOVE REAR FLOOR MAT (for Double Cab)

  17. REMOVE NO. 4 MAT SET PLATE (for Double Cab)

    A01KGPT

    1. Remove the 6 screws and mat set plate.

  18. REMOVE TRANSMISSION SERVICE HOLE COVER SUB-ASSEMBLY (for Double Cab)

    A01KIQM

    1. Remove the 12 bolts and service hole cover.

  19. REMOVE ENGINE SIDE COVER SUB-ASSEMBLY LH (for Double Cab)


    1. for Single Cab:

      Remove the 4 bolts and engine side cover LH.

    2. for Double Cab:

      Remove the 3 bolts and engine side cover LH.

  20. REMOVE EGR COOLER ASSEMBLY


    1. A01KENY

      Loosen the clamp and disconnect the oil return hose.

    2. Loosen the clamp and disconnect water by-pass hose No. 4.

    3. Loosen the clamp and disconnect water by-pass hose No. 2.

    4. A01KGQB

      Remove the 3 bolts and 2 nuts and remove the EGR cooler assembly.

  21. DISCONNECT NO. 3 AIR HOSE


    1. A01KGB1

      Loosen the hose clamp shown in the illustration and separate the No. 3 air hose.

  22. REMOVE DIESEL THROTTLE BODY


    1. A01KGJM

      Disconnect the 2 connectors.

    2. Remove the 2 nuts and 2 bolts and remove the diesel throttle body and gasket.

  23. REMOVE ELECTRIC EGR CONTROL VALVE


    1. A01KFRG

      Disconnect the vacuum regulating valve connector.

    2. Disconnect the 2 vacuum hoses from the vacuum regulating valve.

    3. A01KEYL

      Remove the 2 bolts and remove the vacuum regulating valve with bracket.

    4. A01KHJ4

      Disconnect the electric EGR control valve connector.

    5. Disconnect the vacuum hose from the electric EGR control valve.

    6. A01KGBO

      Disconnect the vacuum hose from the intake air connector.

    7. A01KFHL

      Disconnect the intake air temperature sensor connector.

    8. A01KFC3

      Remove the bolt and separate the manifold stay.

    9. A01KHMN

      Remove the bolt and 2 nuts, disconnect the intake air connector and remove the electric EGR control valve.